PATLITE KG - Manual (Page 2)

100V AC
（ with plug）
12V,24V DC,200V AC
■ Rated voltage
12 ： 12V DC
24 ： 24V DC
100 ： 100V AC
200 ： 200V～240V AC
・ Please process mounting hole to attachment portion.
・ Please fix using attached nuts.
・ Machining of mounting hole is convenient if an attached paper pat tam is used.
･ The direction of the product that you can install is as follows.
〔※〕 The model of the specification of 100V AC has the power cord with plug.
Upright Upside-down Sideway
【 Indoor】
【 Outdoor】
Tighten Remove
Warning
● Turn off the power supply before making wiring connections. Neglecting to so may
cause an electric shock.
● Do not use this product without dome or with cracked dome. It may cause electric shock.
● Make sure power is turned off and the temperature of electric bulb falls down for
repair to avoid electric shock and burn.
● Ask a specialist or an electric engineer about wiring or a construction. Electric shock,
fire and fall may occur.
Caution
● Use only specified operating voltage range. Excess voltage hastens degradation.
● Make sure not to use any other bulbs except ones described in specifications.
● Make sure to set fuse in a power supply side, please connect a fuse. When you use
this product for security purpose, routine inspection must be done.
● Just in case of emergency we recommend you to use this product together with
other security product.
NOTES TO BE OBSERVED FOR SAFE OPERATION
Note to be followed to prevent any damage to the user and other personnel or to assets are as follows:
■
The indications for warning are divided into the following classes according to the degree of danger or
damage incurred when the warning is not taken into consideration and the product is not correctly used.
INSTRUCTION MANUAL
Model : KG
Thank you for specifying for your application. Please read
these instructions carefully before you perform installation, maintenance
and repair. Store this manual carefully for easy reference.
If you have any questions about this product, please contact PATLITE
Corporation.
caution. risk of fire
● Do not put the flammable material, such as paper
or cloth, on the rotating light while it is in
operation. It may cause a fire.
DANGER
Warning Indicates a potentially dangerous condition:
failure to follow the instructions may lead to death or serious injury.
Indicates an imminently dangerous condition:
failure to follow the instructions may lead to death or serious injury. DANGER
Caution Indicates a potentially dangerous condition:
failure to follow the instructions may lead to slight injury or property damage.
K G -
Dome
Bulb
Name plate
Case
Nut
Power supply wires
● Ask a specialist or an electric engineer about wiring or a construction. Electric shock,
fire and fall may occur.
● To avoid lost lighting, electric shock and burnout of power source; do not install the
product horizontally and upside down in the place where it get wet. If water goes into
the product, it will cause short circuit.
● When installing the unit in a high place, choose the place where a foothold can be
secured for case in repairs.
● Follow the precautions below to keep bulb's life from vibration.
(a) Do not install directly on vibrating or shock-producing equipment.
(b) Do not install on a column or a wall experiencing vibration.
Use rigid L brackets in order to prevent swing of the light caused by wind and other
vibrations.
Caution
● Turn off the power supply before making wiring connections. Neglecting to so may
cause an electric shock.
● Confirm the working voltage of the product.
● Wiring should be careful enough there to be for no mistake. If wiring is mistaken, an
internal circuit will be damaged and it will become the cause of a fire.
● Follow the wiring example about wiring.
Be sure to use crimp type terminal connections.
● Make sure to set fuse in a power supply side, please connect a fuse. When you use
this product for security purpose, routine inspection must be done.
● Choose the switches and relays in consideration of starting current.
The starting current must be with in 10 times as high as high as the rated current.
● Do not pull lead wire and push it in case when wiring.
Caution
〔※〕
Power
supply
White
Black
・ KG-12,24
Switch
・ KG-100,200
Fuse
［W iring example］
Red
Black
＋
－
Power
supply
Fuse Switch
● Do not use any bulb other than specified on 8. specification and name plate.
● Make sure power is turned off and the temperature of electric bulb falls down for
repair to avoid electric shock and burn.
● To clean dome and body, wipe with water or glass cleaner soaked soft cloth.
Do not use thinner, benzine, gasoline or oil as these cause color change or deform
the surface.
● Do not lubricate oil to the motor and rotor, it makes the motor stop.
● Do not use the hands to rotate the reflector.
Caution
1. Change Dome
■ Maintenance procedure
・ Check tightening torque of the screws for secure mounting.
・ Change the dome if it is fogged, the fogged dome deteriorates lighting performance.
Please follow procedure mentioned below to change to dome.
（1） Make sure power is turned off when changing dome.
（2） Remove the dome turning it to the left.
（3） New dome is attached, it turns right ward and it attached
in a case.
2. Change Bulb
Please follow procedure mentioned below to change to bulb.
（
1） Make sure power is turned off when changing bulb.
（ 2） Remove the dome turning it to the left.
（ Refer to the "Change dome"）
（ 3） Press the bulb and turn it to the left to detach from
the socket.
（ 4） Fix new bulb into the socket by pressing right ward.
（ 5） The dome is attached.
（ Refer to the "Change dome"）
※ Make sure not to use any other bulbs except ones described in name plate.
Pushing downward
Turn to left
（Remove） Turn to right
（Install）
･The replacement parts prepared. Please ask your local distributor for availability.
･Dome ･Bulb ･Motor ･Rotor rubber
※ If you have question please feel to contact us about other parts.
■ Replacement parts
Please check the list shown below before requesting repairs.
If the product still not work please contact us for repairs.
Please feel free to contact our sales office with any questions concerning the product.
For inquiry, you are required to identify the number indicated at the name plate of the
product.
（ mm） 1. Dimensions
140
120°
120°
50
Name plate
Wire exit hole
3-M8
KG-100：from wire exit（450）
KG-200：from wire exit（390）
KG-12,24：from wire exit（350）
30°
145
50
204
（20
）
186
Installation hole
3- 9
■ Installation
Installation template
Upright Upside-down Sideway
Problems Where to check What to do
Check the power wiring,
plug connection and fuse.
If a switch is installed, check
to see that it is turned on.
If it is, replace it with a new
one.
The motor is broken or has
reached the end of its life.
Request a repair.
Is the power on ? The reflector would
not rotate and the
lamp stays turned
off.
The reflector rotates
but the lamp is off.
Is the light bulb burned out ?
Is the motor stopped ?
Is the motor lubricated ?
The lamp is turned
on but the reflector
stays stopped.
2. Specifications
Rated voltage Model Current
KG -100
KG -12
KG -200
100V AC（50/60Hz）
KG -24
200～240V AC（50/60Hz）
※ Flashing cycle：200Flashes per minute
※ Protection rate：IP23
※ Bulb type：Glass RP35/Base BA15D（KG-100,200）/BA15S（KG-12,24）
Bulb Mass Wire type/die
12V DC
24V DC
0.32A
0.13A
2.7A
1.2A
120V40W
240V30W
12V35W
24V35W
0.9kg
0.7kg
VCT, 0.75mm 2
AV, 1.25mm 2
● We are not in a position to be responsible for damage and trouble caused by
handling against caution and warning described in this instruction manual.
● Specifications may change without notice due to continual product improvement.
Caution
Cover Only KG-100
〔※〕
〔※〕 There is no influence in the quality
though the feel of a material on surface
of the cover might be different.
１． To operate this product safely, please observe the followings.
3 . Parts name
2 ．Model No. configuration
4 ．Installation(Mounting)
5 ．Wiring procedure
6 ．Maintenance
7 ．Before requesting service
8 ．Specifications
'13.12 EPB
A95100182 C