PATLITE BD - Manual

●Make sure that there is no misalignment with the sound group
selection switch when selecting.
If there is misalignment as shown in the figure on the right, the
sound group selected may not play.
6-2. Selecting a Sound Group
Use the sound group selection switch to select a group from the 16 types
from A to P. Use a flat-blade screwdriver with the blade thickness of 1.0mm or
thinner for turning the switch. (Factory default setting: Sound group A)
When the sound group P is selected, any sound may be combined freely
using an SD card. (Factory default setting: See the table below)
Refer to the section 6-3. How to Combine Sounds for details.
Author 13:BEETHOVEN VAN LUDWIG 14:BADARZEWSKA BARANOWSKA TEKLA 15:BACH JOHANN SEBASTIAN
16:SCOTT LADY JOHN DOUGLAS 17･18･21･25･28･29:TRADITIONAL 19･27:PD
20:FOSTER STEPHEN COLLINS 22:Song authorized by the Ministry of Education
23:WERNER HEINRICH (DE 2) 24:STEWART JOHN C26:MOZART WOLFGANG AMADEUS 30:BLANTER MATVEJ ISAAKOVICH
31:WORK HENRY CLAY 32:SCHUBERT FRANZ
Author 13:CREWE BOB 14:CARPENTER RICHARD LYNN 15:JOPLIN SCOTT 16:CARRELL JAMES P
17:Kouichi Sugiyama 18:WILSHAW MICHAEL 19:PACHELBEL JOHANN 20:Ijichi Hiromasa
21:Hiroshi Miyagawa 22:Takeo Watanabe 23,30:Tetsuro Oda 24:CONTI BILL 25:WARREN DIANE EVE
26:Yuka Kawamura 27:KAN 28:Masahiro Andoh 29:Totasu Matsumoto 31:Tatsuya Hirakawa
32:Yumi Matsutoya
Beep (slow intermittent horn)
Rapid Hi-Lo
ＣＨ１
Stutter (rapid intermittent horn)
ＣＨ２
Bell (clear highpitched bell)
ＣＨ３
Yelp (rapid siren)
ＣＨ４
Ａ
Group
Stutter(rapid intermittent horn) Bell(clear highpitched bell) Synthesized Melody Chime
Melody Chime
Chime
Synthesized Piano
Call Sign
Synthesized Bell
Ｃ
Ｂ
Minuet
London Bridge is falling down
Fur Elise
Annie Laurie
Maiden's Prayer
Chime
Chime
Call Sign
Call Sign
Ｅ
Ｄ
Mary had a little lamb The Camptown Races
Holdiridia
Chime
Chime
Call Sign
Call Sign
Ｇ
Ｆ
Amaryllis
Silent Lakeside
Romance De Amour
On the Avignon bridge
Symphony No. 40
Daydream Believer
Chime
Chime
Call Sign
Call Sign
Ｊ
Ｉ
Cuckoo Blacksmith in the village Chime Call Sign Ｈ
Mountain musician
Petrouchka Chime
Chime
Call Sign
Call Sign
Ｌ
Ｋ
Holdiridia
Mary had a little lamb
Grandfather's Clock
Mountain musician
Ave Maria
Stutter(rapid intermittent horn) Bell(clear highpitched bell)
Chime
Synthesized Melody Chime
Call Sign
Ｎ
Ｍ
Romace De Amour Stutter(rapid intermittent horn) Bell(clear highpitched bell) Synthesized Melody Chime
The Camptown Races Cuckoo Petrouchka Grandfather's Clock Ｐ
Ｏ
ＣＨ１ ＣＨ２ ＣＨ３ ＣＨ４
Ａ
Group
Can't Take My Eyes off of You Top of the World
Ｃ
Ｂ
Amairono Kamino Otome
Canon
The Entertainer
Les Champs-Elysees
Amazing Grace Ｅ
Ｄ
Uchuusenkan Yamato Oshiete
Rara Sanshain Ｇ
Ｆ
Aiwa Katsu
Gattsudaze
I Don't Want to Miss a Thing
Truth
Yozorano Mukou Ｊ
Ｉ Makenaide Gonna Fly Now (Theme for "Rocky")
02
01
04
03
06
05
08
07
10
09
12
11
14 Top of the World
13 Can't Take My Eyes off of You
16 Amazing Grace
15 The Entertainer
18 Les Champs-Elysees
17 Amairono Kamino Otome
20 Rara Sanshain
19 Canon
22 Oshiete
21 Uchuusenkan Yamato
24 Gonna Fly Now (Theme for "Rocky")
23 Makenaide
26 Yozorano Mukou
25 I Don't Want to Miss a Thing
28 Truth
27 Aiwa Katsu
30 Odoru Ponpokorin
29 Gattsudaze
32 Haruyo Koi
31 Imasugu Kisu Mi
Ｈ
Imasugu Kisu Mi Haruyo Koi
Odoru Ponpokorin Ｌ
Ｋ
Les Champs-Elysees
Canon
Truth Ｎ
Ｍ
Gattsudaze
Rara Sanshain Uchuusenkan Yamato Odoru Ponpokorin Imasugu Kisu Mi Ｐ
Ｏ
02 Stutter (rapid intermittent horn)
01 Beep (slow intermittent horn)
04 Yelp (rapid siren)
03 Bell (clear highpitched bell)
06 Melody Chime
05 Rapid Hi-Lo
08 Synthesized Bell
07 Synthesized Piano
10 Synthesized Melody Chime
09
12 Call Sign
11 Chime
Stutter(rapid intermittent horn) Bell(clear highpitched bell)
14 Maiden's Prayer
13 Fur Elise
16 Annie Laurie
15 Minuet
18 Holdiridia
17 London Bridge is Falling Down
20 The Camptown Races
19 Mary Had a Little Lamb
22 Blacksmith in the village
21 Cuckoo
24 Daydream Believer
23 On the Avignon bridge
26 Symphony No. 40
25 Amaryllis
28 Mountain musician
27 Silent Lakeside
30 Petrouchka
29 Romance De Amour
32 Ave Maria
31 Grandfather's Clock
Sound groups
Stutter (rapid intermittent horn)
Beep (slow intermittent horn)
Yelp (rapid siren)
Bell (clear highpitched bell)
Melody Chime
Rapid Hi-Lo
Synthesized Bell
Synthesized Piano
Synthesized Melody Chime
Call Sign
Chime
Stutter(rapid intermittent horn) Bell(clear highpitched bell)
Beep (slow intermittent horn)
Rapid Hi-Lo
Stutter (rapid intermittent horn) Bell (clear highpitched bell) Yelp (rapid siren)
Stutter(rapid intermittent horn) Bell(clear highpitched bell) Synthesized Melody Chime
Melody Chime
Chime
Synthesized Piano
Call Sign
Synthesized Bell
Chime
Chime
Call Sign
Call Sign
Chime
Chime
Call Sign
Call Sign
Chime
Chime
Call Sign
Call Sign
Chime Call Sign
Chime
Chime
Call Sign
Call Sign
Stutter(rapid intermittent horn) Bell(clear highpitched bell)
Chime
Synthesized Melody Chime
Call Sign
Stutter(rapid intermittent horn) Bell(clear highpitched bell) Synthesized Melody Chime
We thank you for purchasing PATLITE Audible Alarm. Before you start using the product,
please read this instruction manual carefully to use the product correctly. Please store
this document in a safe place. Be sure to read this document again when you are about
to perform tasks such as maintenance and repair.
And if you have any questions, contact a branch office or the technical support printed on
the last page.
Instruction Manual
Audible Alarm
TYPE : BD
Front panel
The precautions which must be observed to prevent damage to the person using the
product, to people around it, or to property are described in a manner shown below
■The seriousness of injury or damage caused by ignoring the indication and using the
product in a wrong way is categorized with the indications below and descriptions are
added to each of them
Warning
The sections with this indication contain "items which could
cause death or serious injury" if ignored.
The sections with this indication contain "items which could
cause injury or property damage only" if ignored.
Caution
Safety Precautions
●Be sure to turn the power off before wiring or installing the product. Failure to do
so may cause electric shock.
●Take care to perform wiring correctly. If the wiring in incorrect, internal circuit may
be damaged by fire, and it may also be a cause of fire.
●As for the power source, be sure to use this product within the allowable range
of voltage. Failure to do so may be a cause of fire or damage to the product.
●When the product is used for security purposes in which safety is emphasized,
be sure to perform daily maintenance, and design a system which is capable
of tackling the occurrence of unlikely event such as malfunctioning or failure.
●Be sure to let specialists perform installation task which requires construction work.
Failure to do so may cause electric shock, fire, or falling.
●Before you start working on the product, discharge static electricity
from your body. By touching another grounded metal part with bare hand,
the static electricity can be discharged.
●To protect power source circuit and internal circuit of the product,
be sure to install external fuse.
Failures caused by using the product in ways not observing the Warnings and Cautions,
by disassembling or converting the product, or by natural disaster are not covered under
warranty. And do not use the product in ways other than the ways described in this
document.
●Use the product in an environment where there is no electromagnetic or inductive
noise. Speakers are known to generate noise.
●Use the product in an environment where there is no corrosive gas.
Failure to do so may cause malfunction.
●Do not use the product as fire alarm.
1. Cautions Which Must Be Observed for Safety Use
2. Model Indicating Format
3. Part Names
Case
Install the product according to the procedure below.
① Create mounting holes on a mounting surface (board thickness: 1mm - 10mm)
where there is enough space for the mounting hardware. (See the mounting dimensions diagram)
② (a) Insert the product from the front of the mounting surface.
(b) Attach the mounting hardware which comes with the product to the holes on the side of the product.
(c) Then fasten the screws of the mounting hardware. (Recommended fastening torque: 0.7±0.1N・m)
③ Confirm that the product and the mounting hardware are installed properly.
4. How to Install
Sound group
Selection switch
Mounting screw for front
cover (M3X6)
Waterproofing rubber
for the slot
Card slot
Mounting hardware
(attachments)
Terminal cover
(b)
(c)
(a)
Mounting surface
(board thickness: 1mm - 10mm)
SD card
(Model: SDV-2GP Sold separately)
* PATLITE Corporation is a member of
the SD Card Association
Front cover
Volume control
Air duct
□68 mm
Mounting dimensions diagram
* Dimensions of the mounting holes
conform to IEC-61554 (DIN-43700)
Terminal block
(screw M3X6)
■Normal-rated voltage
24 : 12-24V DC
100：100/220Ｖ AC
■Sound Chart type
A：Type A
C：Type C
D：Type D
E：Type E
■Color of body front
J : Light gray
K : Dark gray
+0.7
0
(104mm)
●Be sure to turn the power off before installing the product. Failure to do so may cause electric shock.
●Secure a enough space in which the mounting hardware can also be installed when choosing a mounting surface.
●Install the product on a flat surface without bumps and dips. Failure to do so may weaken its resistance to water and dust.
To prevent the product from falling in places where vibration may be generated, apply thread locking adhesive or the like,
and perform periodic checking of the tightness of the mounting hardware.
●Install the product in a way the air ducts are not blocked.
●Keep a space more than 6.3mm between the terminal block and the metal surface.
●Choose a location for the mounting surface where it has enough strength to support the weight of the product, and where
there is less vibration. Failure to do so may be the cause of injury or damage to the product.
●Be sure to use both pieces of mounting hardware, and fasten them with the recommended fastening torque. Failure to do
so may be the cause of injury or damage to the product.
Before wiring the product, remove the terminal cover. And after the completion of the
wiring attach the terminal cover.
For the external contact of signal line, use no-voltage contact circuit such as relay switch
or open collector circuit (NPN type). As for the contact capacity, see the table below.
5. How to Perform Wiring
Wiring examples
●BD-100
●Be careful not to lose the terminal cover.
●The use of M3 ring terminals with insulating coating is recommended for the wiring of terminal block to prevent
disconnection of wires.Recommended product: N1.25-3 produced by JST Mfg. Co., Ltd.
(Product confirming to RoHS)
●When the product is to be used in a condition in which it is connected to power source, install a switch near the
main body to be able to turn off the power easily for safety reasons.
●Confirm that the wiring has been performed correctly before turning on the power.
●Be sure to turn the power off before you start wiring. Failure to do so may cause electric shock.
●Be careful not to make a mistake in wiring. Moreever wire for neither 100V nor 220V at the same time
in the case of BD-100.
Failure to do so may cause damage to the internal circuit by fire, and it
may cause fire.
●The terminal screws should be fastened with the recommended fastening torque (0.3N・m). Failure to do so may
cause short circuit due to disconnection of wire, and damage to the product.
●When the product is used in places where vibration occurs, perform periodical checking of the tightness of the
terminal screws to prevent letting go of the wires.
●To protect the power source circuit and the internal circuit of the product, be sure to install an external fuse.
No Use
●Sound Chart type A (BD-□A)
Sound List
1mm
12-24V DC
6-1 Opening and Closing the Front Cover
Open or close the front cover according to the procedure shown below when
performing tasks such as adjusting the volume of the sound or selecting the tone color
group.
① Loosen the mounting screw (M3X6) for the front cover.
(An screw does not fall out.)
② Push the lower front cover section (part A in the figure on the right)
lightly with finger to slide it downward.
③ When a SD card is to be used, remove the waterproofing rubber for the slot.
④ After completing tasks, attach the parts removed in the procedure from ① to ③
in the opposite order.
(Recommended fastening torque for the mounting screw: 0.3N・m)
●Be careful not to lose the waterproofing rubber for the slot.
●Do not try too hard to slide down the front cover. To do so may cause the front cover to disassemble.
●Attach the waterproofing rubber for the slot securely. Failure to do so may weaken the product's resistance
to water and dust.
● Fasten the mounting screw for front cover with the recommended fastening torque. In places where
vibrations occur, the front cover may fall or the product may be damaged.
Ａ
6. How to Use the Product
Waterproofing
rubber for the slot
Volume control
Mounting screw
for front cover
(M3X6)
Front cover
Card slot
Sound group
selection switch
Sound groups
●Sound Chart type C (BD-□C)
Sound List
BD - 24 A - J Mounting
hardware
Withstand voltage
Current capacity
Leakage current
ON voltage (Vsat)
DC12V or higher
7mA or higher
0.1mA or lower
1V or lower
(0.5V or lower in case of DC12V)
●Contact capacity
BD-24
BD-100
5.5A/6ms at maximum
None
●Inrush current
Warning
Caution
Warning
Caution
When circuit is opened: DC12V
When circuit is closed: 7mA
COM
CH1
CH2
CH3
CH4
Wiring when
NPN transistor is used
CH side COM side
Fuse
125V 0.5A
Warning
Caution
Other Precautions
Other Precautions
Other Precautions
Other Precautions
Other Precautions
External
point of
contact Sound
Signal line
BD
COM
7mA
←
12V
NPN Open Collector Curcuit
When circuit is opened: DC12V
When circuit is closed: 7mA
COM * Do not connect the power
sources of 100V and 220V
simultaneously.
CH1
CH2
CH3
CH4 Fuse
250V 0.5A
Fuse
125V 0.5A 220V AC
100V AC
Wiring when
NPN transistor is used
CH side COM side
●BD-24 Do not supply a voltage for the signal line.
Failure to do so may be damaged to the product.
C95100106 E