PATLITE BDV - Manual (Page 2)

9. Specifications
4235-A-en
CH1
CH2
CH3
CH4
No.2 No.4 No.3 No.4 No.3 No.3
CH1
CH2
CH3
300ms
CH1
CH2
CH3
CH4
No.15 No.5 No.1 No.1 No.3
CH1
CH2
CH3
CH4
No.4 No.4 No.2 No.2 No.3 No.1
No.2 No.1
CH1
CH2
CH3
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
No.15 No.2 No.15
No.15
No.7 No.3 No.1
No.3
No.1
No.15 No.8 No.10 No.4
No.3 No.2
No.3
CH1
CH2
CH3
CH4
No.4 No.3 No.2 No.2 No.2 No.3 No.1 No.1
No.2
No.1
□80 79.5 15.2
□67.5
15.5
17.2
Front Cover Extension
Length When Opened
[ ] Indicates an interrupted message
No.3
No.6 No.6
Message No.
Signal
Input
Signal Input Timing Chart (Bit Input)
Message No.
Signal
Input
Signal Input Timing Chart (Binary Input)
Input Timing CH (Binary)
Time Delay
About 300ms
within 5ms
Input Held
100ms or more
Input Held
100ms or more
CH
Input2
CH
Input1
Input a binary channel within 5ms, and hold for
100ms or more. other binary channel inputs
are not accepted until the message ends.
Input Timing CH (Bit)
Input Held
100ms or more
100ms
Time Delay
About 300ms
CH
Input
After an input is held for at least 100ms, any
other channel input is not accepted until the
message ends.
Input Stablized
Input Stablized Binary Input
Stablized
100ms Sound
Playback
Sound
Playback
Message No.
CH4
Signal
Input
Input Timing
Sound Reduction Timing Chart (Bit Input)
Sound
Playback Sound
Reduction 100ms or more
CH4 Input
(Sound Reduction)
CH Input
Refer to Sec. 6-5-3 “Bit Input
Sound Reduction Mode”
Interrupt Playback Timing Chart (Bit Input)
Sound
Playback
600ms or less
600ms or less
CH2
Input
CH1
Input
Sound
Playback
CH2
Input
CH1
Input
Message No.
Message No.
Message No.
CH4
Signal
Input
Signal
Input
Signal
Input
Input Timing
Input Timing
Input Timing
Sound Reduction Timing Chart (Binary Input)
Interrupt Playback Timing Chart (Binary Input)
300ms
or more
Sound Reduction
Sound Reduction
Sound
Reduction No.7
Sound
Reduction No.4
Sound
Reduction No.5
Sound
Reduction No.4
Sound
Reduction No.6
Sound
Reduction No.2
Sound
Reduction No.2
Sound
Reduction No.2
Sound
Reduction No.3
Sound
Reduction No.3
Message No.
Signal
Input
Input Timing
Hold Playback Timing Chart (Bit Input)
Sound
Playback
CH2
Input
CH1
Input
600ms or less
Message No.
Signal
Input
Input Timing
Hold Playback Timing Chart (Binary Input)
Sound
Playback
CH2
Input
CH1
Input
600ms or less
8. Before Requesting Repair
7. Options and Accessories
【Outer Appearance Drawing】
Mounting Angle
(Accessory)
Unit: mm
Model BDV-15JF BDV-15KF
Rated Voltage 12 - 24V DC 100V AC (50/60Hz) 220V AC (50/60Hz)
Power Consumption Max. 4W Max. 5W
Voltage Range 10.8 - 26.4V DC 100V AC ±10% 220V AC ±10%
Sound Pressure Level
Audio File
File Format
Internal Memory Size
Number of Playback Messages
Operating Temperature Range
Relative Humidity
Mounting Direction
Protection Rating
Insulation Resistance
Withstanding Voltage
Vibration Resistance
Mass
MPEG1 Audio Layer III (MP3) Standard Bit Rate: 64kbit/s, Fs=44.1kHz (CD Quality)
FAT16
Bit Input: 4 / Binary Input: 15
85% RH or less (no condensation)
220g ±10% 340g ±10%
←Upright
Position
←Sideways
Position
Inverted
Position →
IP54 (Upright Direction for Panel Mount only)
1M Ω or more (at 500V DC) between terminal and chassis
500V AC for 1 minute 1500V AC for 1 minute
(Between terminal and chassis)
At 30Hz in directions from back and fourth, left and right, up and down for 2 hours
19.6m/s 2 (Upright Position)
Indoor: Upright, sideways and inverted mounting (Use Upright if water splashing is present) Outdoor: Upright Direction Only
-10 to +50 ℃
508kB (MP3 data total)/ Maximum playback time 63sec (at Standard Bit Rate)
Max. 87dB: Placed on a 300mm 2 base at a distance of 1 meter with a 1kHz sine wave at a -6dB input.
Volume Adjustable ※Sound level of message will vary with the surrounding environment.
● As the sound increases, the possibiliy of distortion may also occur.
● Due to environmental conditions and tolerances. the volume may not be at zero sound level.
● The volume is turned half-way at the factory prior to shipment.
NOTE
● Although a pop noise may occur when the playback is controlled via the power supply or
playback start and finish, it is not an indication of failure.
● Even when starting two or more units simultaneously, a lag will occur during message
playback.
NOTE
● Turn the volume control lightly, a torque over 0.3N・m can damage the volume control.
PLEASE
1
1
1
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
0
0
0
1
1
1
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
1
Binary Input Table
Message
No. CH1 CH2 CH3 CH4 Message
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CH1 CH2 CH3 CH4
6-4. Volume Adjustment
The sound level can be adjusted by the volume control.
Use a flat-head screwdriver with a blade width of 1.0mm or
thinner for turing the volume control.
Increase
Volume
Decrease
Volume
1mm
6-5. Message Playback
Turn the product on and short-circuit the signal line to the common line to for operation.
・ Short-circuit the signal wire to common for 100ms or more (Pulse input).
・ When controlling this product via the power supply, the start-up takes about 500ms
before the sound can play back.
・ The input timing for all modes and all the CH inputs are the same for when playing back
messages. Please refer to the Input Timing Chart below for operation.
・ When two or more signal wires are short-circuited at the same time to the common lines
for bit input, the higher channel takes priority (bit input only).
Priority Input Order： CH4＞CH3＞CH2＞CH1
6-5-1. Bit Input Mode (Operation Mode Switch: A)
If signal wires from CH1 to CH4 are short-circuited to the common, the message of the
selected channel will play back.
6-5-2. Binary Input Mode (Operation Mode Switch: B)
If signal wires from CH1 to CH4 are short-circuited to the common, the message
corresponding to the binary input conversion table will be played back.
(Refet to the “Binary Input Table”)
※ A”1” in the table refers to the short-circuit of the signal line to the common line.
6-5-3. Bit Input Sound Reduction Mode (Operation Mode Switch: C)
CH1 to 3 corresponds to Bit Inputs. CH4 Input reduces the volume by 10dB.
・ CH4 has no input priority.
・ When multiple messages are entered during playback, the next message will be reduced.
・ In some cases, the message will be reduced by 10dB during playback.
6-5-4. Binary Input Sound Reduction Mode (Operation Mode Switch: D)
CH1 to 3 corresponds to Binary Inputs. CH4 Input reduces the volume by 10dB.
・ CH4 has no input priority.
・ When multiple messages are entered during playback, the next message will be reduced.
・ In some cases, the message will by reduced by 10dB during playback.
6-5-5. Bit Input Interrupt Playback Mode (Operation Mode Switch: E)
When one of the signal wires from CH1 to CH4 are entered for a bit input and an input
message is entered during message playback, the message will interrupt the message
being played.
・ Even if the input is held down, the message playback will be reproduced only once.
・ There is no Priority Input Order
6-5-6. Binary Input Interrupt Playback Mode (Operation Mode Switch: F)
When one of the signal wires from CH1 to CH4 for a binary input are entered and an
input message is entered during message playback, the message will interrupt the
message being played.
・ Even if the input is held down, the message playback will be reproduced only once.
・ There is no Priority Input Order
6-5-7. Bit Input Hold Playback Mode (Operation Mode Switch: G)
If the signal wires from CH1 to CH4 for a bit input are held when short-circuited to
common, the message will repeat until the signal wire is removed from common.
・ Once the input is lost, the playback will stop.
6-5-8. Binary Input Hold Playback Mode (Operation Mode Switch: H)
If the signal wires from CH1 to CH4 for a binary input are held when short-circuited to
common, the message will repeat until the signal wire is removed from common.
・ Once the input is lost, the playback will stop.
6-5-9. Test Playback (Operation Mode Switch: I through P)
Message from CH1 continues being played back. Any other CH inputs are ignored during
test playback.
・ Use the “Test Playback Mode” when checking the operation or adjusting the volume.
・ To operate in the “Test Playback Mode”, select the “Operation Mode Switch” to any
mode from “I” to “P”.
・ Because the “Test Playback Mode” automatically resets the “Operation Mode” to ‘A’,
reboot the product after exiting the “Test Playback Mode” in order for the new settings to
take effect.
■ SD Card: Model SDV-128P
The SD Card is used when changing the messages for the Voice Annunciator product.
■ Voice Playlist Editor: Model FV-Win
MP3 Editor software.
● Even after proper installation and handling, if the product does not operate correctly,
contact your PATLITE Sales Representative.
Problem Where to Check What to do
No
Sound
Different
Channel
Plays Back
Cannot
Record
Message
SD Card not
being read
Is there power supplied?
Is the signal line to common line short-
circuited correctly?
Is the volume turned down to minimum?
Is the signal line to common line short-
circuited correctly?
Is the Operation Mode Switch set correctly?
Is there power supplied?
Is the playlist created on the SD card?
Is the file name and contents of the playlist
folder right?
Is the data storage location correct?
Is the SD card an option product from our
company?
Is the SD card inserted correctly?
Is the volume turned down to minimum?
(Overwrite beep may not be heard)
Is the “SDV-128P being used?
Is the SD Card correctly inserted?
Double check the wiring. (5. Wiring)
Double check the SD Card.
(6-3. Message Rewriting)
Double check the contents of the SD Card
Playlist and Data Folder.
(FV-Win or Patlite
Playlist Editor Help File.)
Double check the wiring. (5. Wiring)
Double check the wiring. (5. Wiring)
Double check the SD Card.
(6-3. Message Rewriting)
Adjust the volume. (6-4. Volume Adjustment)
Double check the Selection Switch.
(6-2. Playback Mode Selection)
Adjust the volume. (6-4. Volume Adjustment)
● Despite the cautions and warnings provided in this manual, it is not the responsibility of
PATLITE for any failure or damage occured from mishandling.
● Due to changes, improvements, etc., the contents of this manual may change without
advance notice.