3.2.5. analogue outputs, 3.3. genesis i digital controller, 3.3.1. digital outputs – Innotech Genesis V4 System User Manual
Page 38: Digital outputs (paragraph 3-3.3.1), Analogue inputs (paragraph 3-3.3.2), Analogue outputs (paragraph 3-3.3.3), Rs485 comms terminals (appendix a), Rs23, 2 connector (appendix a)
Installation Instructions for Innotech Genesis Systems
Edition 011100
3-12
NOTE
Two terminals, located between the Digital and Analogue Input
terminal groups (Figure 3-4), are provided for terminating cable
screens.
3-3.2.5.
Analogue Outputs.
The Genesis II MPC’s analogue output wiring
information is similar to that of the Genesis II Digital Controller (refer to Paragraph 3-
3.1.5), with the following exceptions:
•
The MPC only uses four analogue output channels: AO1 through AO4.
•
Terminal numbers are not assigned, however terminals are clearly labeled as to signal
name: The two centre terminals of the group of six analogue output terminals are the
signal return (Common) connection points.
3-3.3.
GENESIS I DIGITAL CONTROLLER.
Figure 3-5 shows the input/output
connection groups for the Genesis I Digital Controller. The controller uses Phoenix type plug-
in terminal strips located around the controller’s perimeter. Terminals are grouped by function
as follows:
•
Power – Same as for Genesis II Digital Controller; see Paragraph 3-3.1.1.
•
Digital Inputs – Same as for Genesis II Digital Controller; see Paragraph 3-3.1.2.
•
Digital Outputs (Paragraph 3-3.3.1)
•
Analogue Inputs (Paragraph 3-3.3.2)
•
Analogue Outputs (Paragraph 3-3.3.3)
•
Local Expansion Module (LEM) Connector (Paragraph 3-3.3.4)
•
RS485 Comms Terminals (Appendix A)
•
RS23
1
0
1
1
1
2
1
3
1
4
1
5
1
6 1
7
1
8
3
4
5 6
7
8
9 1
9
2
0 2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5 3
6
2
1
2
2
2
3
2
4 2
5
2
6
2
7
4
8
5
0
5
1
5
3 5
4
5
6
5
7
5
9
6
0
6
2
6
3
4
1
4
2
4
4
4
5
4
7
7
8
6
5
6
6
6
7
6
8
6
9
7
0
7
7 8
9
9
0
9
1
9
2
9
3
1
2
2
4
V
a
c
P O
W
E
R
S
C
R
E
E N
S
D
IG
IT
A L
IN
P
U
T
S A
N
A
L
O G
U
E
IN
P
U
T
S
A
N
A
L
O G
U
E
O
U
T
P
U T
S
R
S
4
8
5
C
O
M
M
S R
S
2
3
2
C
O
N
N
E C
T
O
R
D
IG
IT
A L
O
U
T
P
U
T
S
L
E
M
C
O
N
N
E C
T
O
R
2 Connector (Appendix A)
3-3.3.1.
Digital Outputs.
The Genesis I Digital Controller’s digital output wiring
information is similar to that of the Genesis II Digital Controller (refer to Paragraph 3-
3.1.3), except that the NC output relay contacts are not used. Only the C and NO contacts
of the eight digital output relays are represented at the output terminals. Refer to Table 3-7.