Dwyer IPV - Manual

IPV Series Air Hammers
• One impact wave caused by one shot
• High strength aluminum structure
• Impact force and interval timing can be set based on requirement
• Magnetic hammer stores magnetic strength to increase the piston’s
impact power
Series IPV Air Hammer (single impact model) focuses on a limited
target. Other equipment of the target is minimally affected by it. The air
hammer’s impact won’t separate water out of humid mixtures. It is often
applied onto a pipe or clean elbow in a tank filled with humidity or low
specific gravity material.
HOW IT OPERATES
The IPV series air hammer contains a powerful magnet inside the
hammer. The hammer and magnet are tightly closed before activation.
However, as the inlet air pressure gets higher than the force, this
tightens the hammer and magnet. The hammer and magnet will
separate and cause more strength for impact power. The spring will
bring the hammer back to the initial position automatically after the
impact. By doing this, the air pressure will be released and the strength
of the air pressure will be delivered to the target impact container. It will
help to smooth the flow and prevent accumulation inside the container.
Series IPV Air Hammer
Specifications - Installation and Operating Instructions
Bulletin P-14
PROXIMITY CONTROLS
Phone: 219/879-8000 www.dwyer-inst.com
A DIVISION OF DWYER INSTRUMENTS, INC. Fax: 219/872-9057 e-mail: [email protected]
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.
IN
OUT
A
D
ØH
ØC
ØB
SPECIFICATIONS
Temperature Limit: 212°F (100°C).
Noise Level Range: 60-75 dBA.
Supply Pressure: 43.5 to 87 psi (3 to 6 bar).
Air Consumption: See model chart.
Air Connection: 1/4˝ BSPT female with 1/4˝ OD push to connect
adapter on IPV-1, IPV-2 and IPV-3; 3/8˝ BSPT female with 3/8˝ OD push
to connect adapter on IPV-4. Also includes muffler for exhaust port.
Model
IPV-1
IPV-2
IPV-3
IPV-4 A
5.43˝ (138 mm)
6.54˝ (166 mm)
8.19˝ (208 mm)
10.56˝ (269 mm) øB
3.15˝ (80 mm)
3.94˝ (100 mm)
5.51˝ (140 mm)
6.77˝ (172 mm) øC
2.36˝ (60 mm)
2.95˝ (75 mm)
4.13˝ (105 mm)
5.51˝ (140 mm) D
0.47˝ (12 mm)
0.63˝ (16 mm)
0.63˝ (16 mm)
0.94˝ (24 mm) øH
0.35˝ (9 mm)
0.43˝ (11 mm)
0.59˝ (15 mm)
0.75˝ (19 mm) Connection
1/4˝
1/4˝
1/4˝
3/8˝
Impulse
lbf•s (N•S)
Air Consumption
in 3 (l) per stroke
Weight
lb (kg)
2.43 (1.1)
3.97 (1.8)
8.82 (4.0)
18.52 (8.4)
Model
IPV-1
IPV-2
IPV-3
IPV-4
.225 (1.0)
.630 (2.8)
1.66 (7.4)
2.81 (12.5) 1.71 (0.028)
5.0 (0.082)
14.0 (0.228)
27.8 (0.455)