Asus Motherboard P5LD2-VM DH - Manual (Page 38)

1 - 2 6 1 - 2 6 1 - 2 6 1 - 2 6 1 - 2 6 C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
1.10.2 1.10.2 1.10.2 1.10.2 1.10.2 Internal connectors Internal connectors Internal connectors Internal connectors Internal connectors
1 . 1 . 1 . 1 . 1 . F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using an FDD cable with a covered Pin 5.
®
P5LD2-VM DH
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
P5LD2-VM DH Floppy disk drive connector
PIN 1
FLOPPY
e
2 . 2 . 2 . 2 . 2 . P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
These connectors are for Ultra DMA 133/100/66 signal cables. There are
three interfaces on each Ultra DMA 133/100/66 signal cable: blue, black,
and gray. Connect the blue interface into the motherboard’s IDE connector,
then select one of the following modes to configure your hard disk drive(s).
C a b l e S e l e c t M o d e C a b l e S e l e c t M o d e C a b l e S e l e c t M o d e C a b l e S e l e c t M o d e C a b l e S e l e c t M o d e - use this mode to select the operating mode by
cable connectors.
No. of drives Drive type Drive jumper Cable connector
1 With OS black
2 With OS Cable select black
Without OS gray
J u m p e r S e l e c t M o d e J u m p e r S e l e c t M o d e J u m p e r S e l e c t M o d e J u m p e r S e l e c t M o d e J u m p e r S e l e c t M o d e - use this mode to select the operating mode by
hard disk drive jumper.
No, of drives Drive type Drive jumper Cable connector
1 With OS Master
2 With OS Master black or gray
Without OS Slave