Triton RL5000 TDM100_150 Quick Reference Guide - Manual (Page 2)

CASSETTE / DAY CLOSE REPLACING RECEIPT PRINTER PAPER
SELECT DAY CLOSE OPTION. SELECT PRINT OPTION TO PRINT A RECEIPT. NOTE: IF ATM DAY CLOSE IS
NOT PERFORMED AT SAME TIME AS PROCESSOR, HOST SETTLEMENT AMOUNT MAY NOT MATCH TER-
MINAL SETTLEMENT AMOUNT ON DAY CLOSE RECEIPT.
JOURNAL
ACCESS MANAGEMENT FUNCTIONS USING ACCESS INSTRUCTIONS AND SELECT THE ELECTRONIC JOUR-
NAL OPTION. TO CLEAR THE JOURNAL: SELECT THE CLEAR JOURNAL OPTION. THIS WILL MARK ALL
UNAUDITED JOURNAL RECORDS. AUDITED RECORDS MAY BE PRINTED USING THE DISPLAY LAST X OR
VIEW JOURNAL ARCHIVE OPTIONS.
ACCESS MANAGEMENT FUNCTIONS USING ACCESS INSTRUCTIONS AND SELECT THE ELECTRONIC JOUR-
NAL OPTION. TO PRINT THE JOURNAL, SELECT THE DISPLAY UNAUDITED RECORDS. A PRINT OPTION IS
AVAILABLE TO PRINT ALL RECORDS THAT HAVE NOT BEEN AUDITED. THE RECORDS WILL BE MARKED.
TO PRINT PREVIOUSLY AUDITED OR PRINTED JOURNAL RECORDS, USE THE DISPLAY LAST X OR VIEW
JOURNAL ARCHIVE OPTIONS.
REPLENISHING CASSETTE (TDM-100/150)
2
6
4
1 5
7 3
UNLOCK/OPEN CABINET. PULL MECHANISM OUT
ON SLIDE TRAY TO ITS FULLY EXTENDED
POSITION.
REMOVE NOTE CASSETTE. UNLOCK AND OPEN
CASSETTE. LOAD CURRENCY. CLOSE, LOCK AND
INSTALL NOTE CASSETTE.
REMOVE REJECT CASSETTE. UNLOCK AND
OPEN CASSETTE. REMOVE ANY NOTES. DO NOT
RECYCLE REJECTED NOTES!. CLOSE, LOCK AND
INSTALL REJECT CASSETTE.
WITH MECHANISM INOPERATING POSITION,
CLOSE AND LOCK CABINET.
REPLENISHING CASSETTE (TDM-100/150)
1
4
7
CUT REMAINING PAPER TO ALLOW
REMOVAL. PRESS FEED BUTTON TO CLEAR
PAPER FROM PAPER PATH. LIFT SPINDLE TO TAKE-OUT HOLE
AND REMOVE PAPER ROLL AND
SPINDLE.
REMOVE SPINDLE FROM OLD
PAPER ROLL. PLACE SPINDLE IN NEW PAPER
ROLL.
FEED END OF PAPER INTO FEED
SLOT.
PLACE NEW PAPER ROLL ON
BRACKET. MAKE SURE PAPER FEEDS
FROM TOP!
PAPER WILL FEED AUTOMATI-
CALLY.
CASSETTE CLOSE
2
6 5
3
8
THIS AREA FOR SERVICE PROVIDER
CONTACT INFORMATION:
STEP ACTION STEP ACTION STEP ACTION
STEP ACTION ACTION STEP ACTION STEP ACTION STEP
DAY CLOSE
1. GO TO MANAGEMENT FUNCTIONS USING ACCESS INSTRUCTIONS. SELECT TERMINAL CLOSE FUNCTIONS.
CHOOSE CASSETTE CLOSE OPTION. ENSURE CASSETTE A IS CHECKED ( ) SELECT ENTER TO CLEAR
THE TOTALS. SELECT PRINT OPTION TO PRINT A RECEIPT.
2. REPLENISH CASSETTE PROMPT APPEARS. REMOVE CASSETTE. COUNT CASH. CASH IN CASSETTE (IN-
CLUDING REJECT NOTES) SHOULD EQUAL REMAINING AMOUNT VALUE ON RECEIPT.
3. LOAD CASSETTE, USING REPLENISHING CASSETTE PROCEDURES. REPLACE CASSETTE. PRESS ENTER
WHEN COMPLETE. ENTER NUMBER OF BILLS LOADED IN CASSETTE AND PRESS ENTER. TRIAL CAS-
SETTE CLOSE PROMPT APPEARS. SELECT PRINT OPTION TO PRINT A RECEIPT AS RECORD OF BEGIN-
NING CASSETTE BALANCE. PRESS ENTER WHEN DONE.
CLEAR JOURNAL
PRINT JOURNAL
PULL LOCKING PIN TO ALLOW MECHANISM TO
SWIVEL ON SLIDE TRAY.
ROTATE MECHANISM TO ALLOW ACCESS. RELEASE
LOCKING PIN.
PULL LOCKING PIN. ROTATE MECHANISM TO
OPERATING POSITION. RELEASE LOCKING PIN.
TDM-150 DISPENSING MECHANISM
(SHOWN BELOW)