Tennsco Electronic Workbench - Manual (Page 2)

Step By Step Installation Instructions
(Proceed to next step on optional items not purchase)
Tools required: Slotted screwdriver, Phillips screwdriver, and 7/16" & 3/8" wrenches or nut drivers (use 2 people for assembly).
1. Place the panel legs (1) in an upright position as shown
in Figure 1 of the assembly drawings. The legs should
be placed approximately 53" apart for 60" units and
65" apart for 72" units.
2. Place receptacle panel (2) inside panel legs and
secure with four 1 ⁄
4
"-20 x 5 ⁄
8
" bolts and nuts. (Stringer
mounting holes go to the rear.)
3. Attach stringer (4) [provided with top] to back of panel
legs as shown. Fasten with eight 1 ⁄
4
"-20 x 5 ⁄
8
" bolts,
nuts and washers.
4. Set back panel (3) inside panel legs and secure with
four 1 ⁄
4
"-20 x 5 ⁄
8
" bolts and nuts.
5. OPTIONAL Wiring Kit
5a. Install optional wiring kit (WK-1) into receptacle
panel using the instructions provided with each
wiring kit.
DO NOT CONNECT POWER TO UNIT UNTIL
ENTIRE UNIT HAS BEEN ASSEMBLED.
6. Attach the wireway cover (5) to the back bottom flange
of the receptacle panel with four #10 sheet metal
screws.
7. Attach bench top (6) to frame assembly using the
applicable instruction below:
Solid Maple Top; Compressed Wood on
Wood Top;
or Plastic Laminate Top (Figure 2):
7a. Place bench top on a smooth, non-marring
surface with top side facing down.
7b. Attach leg assembly to under side of bench
top through pre-drilled holes. Secure with
#14 x
3 ⁄
4
" wood screws: six in each panel
leg; six in receptable panel; and six in back
panel.
NOTE: When installing a 30" x 60" wood
top, the pre-drilled holes will not align. Use
a
5 ⁄
32
" drill bit to drill pilot holes along the
front and back edges of bench top for
attaching receptacle panel (2) and back
panel (3).
Steel Top (Figure 3):
7a. Place bench top on a smooth, non-marring
surface with top side facing down.
7b. Attach leg assembly to under side of bench
top through punched holes. Secure with
1 ⁄
4
"-20 x 5 ⁄
8
" bolts and nuts: one in second
hole from each corner of top; eight in
receptacle panel; and eight in back panel.
7c. Insert channel (7) in each end of bench top.
7d. Align bench top, panel legs, and channel
holes. Secure with four 1 ⁄
4
"-20 x 5 ⁄
8
" bolts.
Note four weld nuts are provided on
channels.
8. Set bench assembly upright and recheck all nuts, bolts
and screws for tightness.
9. OPTIONAL Stackable Drawer Attachment (Figure 4):
9a. Remove drawer (15) from housing (16).
9b. Secure lock hasp (17) to housing top using the two
1 ⁄
4
"-20 x 5 ⁄
8
" bolts extended down from top of
housing.
9c. Secure long mounting brackets (14) to rear of
housing, with bracket flanges turned downward,
using four
1 ⁄
4
"-20 x 5 ⁄
8
" bolts and nuts. Bracket
should extend 10 1 ⁄
2
" behind housing. (NOTE:
When installing drawer onto a wood top, drawer is
secured directly into the wood top; no mounting
brackets are used. Holes must be drilled as
needed.)
9d. E N S U R E T H A T W O R K B E N C H P O W E R
SUPPLY IS NOT CONNECTED BEFORE
PERFORMING NEXT STEP.
9e. Attach drawer unit to workbench by removing
wireway cover from receptical housing and
aligning front slots in top of housing with holes in
receptacle panel (short mounting brackets are not
used). Secure with two
1 ⁄
4
"-20 x 5 ⁄
8
" bolts and nuts.
9f. Align holes in mounting brackets with holes in back
panel flange and secure with two 1 ⁄
4
"-20 x 5 ⁄
8
" bolts
and nuts.
9g. Replace wireway cover.
9h. Insert drawer in housing.