Arcam AVP700 - Manual (Page 13)

AVP700
E-12
AVP700
E-13
HQ Video: Choose between RGB or YUV ; if you have a YUV display, set this item to YUV , otherwise
set it to RGB .
This setting controls the routing of the HQ-video within the AVP700, either as 3-wire YUV or 4-
wire RGB signals (with the synchronisation signal on composite for RGB). In addition, it controls
the operation of the S-video/composite-to-HQ video converter.
When set to YUV, incoming composite and S-video signals are converted to YUV; in RGB mode,
the incoming signals are converted to RGB, with the synchronisation signal on the composite
output.
This setting has no effect on the HDMI output.
2 – Speaker Sizes
The size and number of loudspeakers are defi ned on this page.
Auto Set-up: Allows the setting of ‘standard confi gurations’ as in the table below:
Speaker Confi g. 1 Confi g. 2 Confi g. 3 Custom
Front L/R Small Large Large Small/Large
Centre Small Small Small Small/Large/None
Surr L/R Small Small Large Small/Large/None
Surr Back L/R Small Small Small Small/None
Sub-woofer Present None Present Present/None
5.1 Rears Both Both Both Surr L/R/
Sur Back L/R/
Both
The Custom setting allows you to choose any combination of speakers to suit your system. Note that
the centre and rear speakers cannot be set to ‘large’ if the front speakers are set to ‘small’.
5.1 Rears defi nes how the speakers in a full ‘7.1’ installation handle 5.1 decoded sources.
< SURR L/R redirects 5.1 surround signal to the surround left and right speakers. No signal will be
directed to the surround back left or right speakers.
< SURR BACK L/R redirects 5.1 surround signal to the surround back left and right speakers. No
signal will be directed to the surround left or right speakers.
< BOTH redirects the 5.1 surround signal to both pairs of speakers with the signal to each set
reduced by 3dB.
A note on speaker sizes:
A Large speaker is one that is capable of handling a full range signal (i.e., 20Hz–20kHz).
A Small speaker is one that is not capable of reproducing a deep bass signal (i.e., below 100Hz),
for example a satellite speaker.
None indicates that there is no speaker connected to that channel.
3 – Sub woofer Settings
If no sub woofer was selected in the previous speaker menus then some of the items on
this page will not be adjustable.
Cross-over Freq.: This setting defi nes the frequency at which bass redirection begins.
Frequencies below this level are redirected from ‘small’ speakers to the Fronts or to
the sub woofer; frequencies above this level are not redirected. The value for this
setting depends on your speakers, environment and taste, and is best determined by
experimentation.
The adjustment can be made in increments of 10Hz between 40Hz and 130Hz.
Stereo Mode: Select between Large, Large+Sub or Sat+Sub.
If you have confi gured your system to have a sub woofer, then you have the fl exibility
to choose how bass information is distributed between the front left/right speakers and
the sub woofer when listening to stereo sources. Choose the option which gives you the
most solid even sounding bass (for best results test with a set-up disc or live program material).
< LARGE : Pure stereo information — all audio is sent to the front left and right speakers. Use this
setting if you have large front speakers.
Note that this option will override the setting confi gured on the “Speaker Sizes” menu page.
< LARGE+SUB : Pure stereo is fed to left and right and extracted bass is sent to the sub woofer. In
this case the low frequency information is, effectively, duplicated.
< SAT+SUB : Use this setting if you have ‘Small’ satellite left and right speakers. Full bass
management is used in analogue stereo so that analogue sources are fed to the DSP where the
bass is fi ltered off left and right and redirected to the sub woofer.
Note that the above three Stereo Mode settings pass the audio through the signal processor of the
AVP700, which may degrade the sound quality slightly. This can be avoided for the ‘Large’ setting by
pressing the
DIRECT button to bypass this processing.
DTS LFE Gain: DTS soundtracks typically have the LFE track recorded 10dB lower than the main audio
tracks. It is, therefore, necessary to compensate for this by raising the LFE output level by 10dB, and
setting the DTS LFE gain to ‘Normal’ activates this compensation. Some DTS soundtracks have been
recorded with the LFE signal at the same levels as the main audio, however, and therefore require no
gain compensation. For these disks set the DTS LFE gain to -10dB.
< NORMAL : This increases the LFE signal by 10dB and is the recommended setting for the AVP700.
< -10DB : This allows the LFE to pass directly to the output with no gain adjustment.
Unfortunately, there is no rule for determining which discs are recorded using which method. As a
general guide, however, it is only early DTS music discs that require the -10dB setting.