Accessories – Lincoln Electric IM537 SP-170T User Manual

Page 32

C-1

ACCESSORIES

OPTIONAL ACCESSORIES

1. K549-1 .035" (0.9 mm) Innershield® Welding Kit

— Includes a contact tip, a gasless nozzle and a
.035/.045" (.9/1.2 mm) cable liner to permit the
Magnum™ 100L gun and cable to use .035" (0.9
mm) diameter flux-cored electrode. The fitting on
the end of the liner is stenciled with the maximum
rated wire size (.045"/1.2 mm). Also included is a
10 lb.(4.5 kg.) spool of .035" (0.9 mm) Innershield

NR-211-MP.

See “Innershield (FCAW) Conversion” in this sec-
tion for installation instructions and MAINTE-
NANCE section for proper feeding component con-
figuration and installation.

2. K549-2 .045" (1.2 mm) Innershield® Welding Kit

— Includes a contact tip, a gasless nozzle and a
.035/.045" (0.9/1.2 mm) cable liner to permit the
Magnum™ 100L gun and cable to use .045" (1.2
mm) diameter flux-cored electrode. The fitting on
the end of the liner is stenciled with the maximum
rated wire size (.045"/1.2 mm). Also included is a
10 lb.(4.5 kg.) spool of .045" (1.2 mm) Innershield

NR-211-MP and a knurled drive roll.

See “Innershield (FCAW) Conversion” in this sec-
tion for installation instructions and MAINTE-
NANCE section for proper feeding component con-
figuration and installation.

3. K664-2 Aluminum Feeding Kit — This kit required

for welding with .035 Aluminum wire. Included with
this kit are a drive roll, cable liner and .035 contact
tip. It is important when changing between
welding with steel wire and aluminum to
exchange feeding components due to the lubri-
cant applied to steel wire. Failure to do so may
result in contaminated welds when welding alu-
minum.

See Maintenance section for instructions on
installing drive roll, cable liner, contact tip and their
proper configuration.

4. KP665-045C Drive Roll – Optional — Knurled

drive roll for feeding .035 - .045” (0.9 - 1.2 mm)
diameter flux-cored electrode.

5. K695-1 Spot / Stitch Timer Kit — Includes spot

timer to control the spot welding arc time, and a
stitch timer to control the on/off cycle time of the
arc to prevent burnthrough on thin gauge metals.
Also includes spot welding nozzle.

The Spot/Stitch Timer Kit installs inside the wire

feed compartment, replacing the blank panel locat-
ed below the gun trigger lead connectors, per the
installation instructions (M17920) included with the
kit.

6. K520 Utility Cart — Designed to transport the

Lincoln family of small welders. Has provisions for
mounting a single gas cylinder. Has front casters
and large rear wheels. Handle height is easily
adjustable. Bottom tray provided for tools and
accessories. Easy assembly required; takes less
than 15 minutes.

7. K1800-1 CO

Gas Regulator & Hose Kit —

Includes an adjustable pressure and flow regulator
for use on CO

cylinders. Also included is a gas

hose which connects to the rear of the welder.

See “Gas Connection” in Installation section for
installation instructions.

8. K1799-1 Argon-Mixed Ajustable Gas Regulator

and Hose Kit

(1)

— Includes an adjustable pressure

and flow regulator for use on argon-mixed gas
cylinders. Also included is a gas hose which con-
nects to the rear of the welder.

9. K586-1 Deluxe Adjustable Gas Regulator &

Hose Kit
Accommodates CO

or mixed Gas Cylinders.

10. K697-2 Power Cord Extension — Extension

230V power cord (20’/6.1m) allows extra conve-
nience when work is located some distance away
from power receptacle.

11. K667-1 230 Volt 50 Amp Receptacle — For pro-

viding power for your SP-170T at your welding
location. NEMA standard 6-50 R receptacle. See
“Line Cord Connection” in INSTALLATION section
for recommended wire size.

(1)

This regulator comes standard with a 4.5 foot hose
with the SP-17OT.

SP-170T