Pfister A51-ANFC - Manual (Page 2)

English: Thank you for purchasing this Price Pfister
product. All Price Pfister products are carefully engineered,
and factory tested to provide long trouble-free use under
normal conditions. This product is easy to install using
basic tools and our easy to follow illustrated instructions. If
you have any questions regarding this product, see info on
previous page.
1 BEFORE PROCEEDING
WARNING: Read all the instructions completely before
proceeding. Price Pfister recommends calling a professional
if you are uncertain about installing this product!
This product should be installed in accordance with all local
and state plumbing and building codes.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply
valves. These are usually found under the sink or near the
water meter. If you are replacing an existing faucet, remove
the old faucet from the sink and clean the sink surface
thoroughly.
3 ASSEMBLY INSTRUCTIONS
If operating pressures exceed 5 BAR (~75 PSI), the use of a
pressure reducer is recommended. Before proceeding with
the assembling, we advise to clean the water tube, in order to
avoid build-up of dirt that could compromise the functioning
of the faucet.
4 FAUCET INSTALLATION (Fig.A)
Place the base ring (1) and o-ring (2) on the threaded post
(3). Insert the threaded post (3) into hole (4) in sink top so
that the base sits flat to the sink surface and faucet body
(5) stands upright. Verify the correct position of the o-ring
(2). From underneath the sink top slip the flange (6) over the
threaded post until it is flush with undersurface of sink top.
Secure faucet body (5) by tightening the nut (7).
5 DRAIN MOUNTING (Fig.A)
The drain body (23) can be installed with or without rubber
seal (22). If drain body (23) is installed without rubber seal
(22), apply a small bead of plumber’s putty underneath
the flange (23) and around drain opening (24). Use
PTFE plumber’s tape to all threaded fittings according to
manufacturer’s instructions. From above, insert drain body
(23) into drain opening (24). From underneath, place rubber
washer (21) and friction washer (20) over threads of drain
body (23). Thread drain nut (19) onto drain body (23) until
firmly secured in drain opening (24). Connect pipe extension
(17) to drain body (23) by threading wingnut (16) to bottom
of to drain nut (19). Be sure that washer (18) is placed in
between drain nut (19) and pipe extension (17) as shown.
6 WATER SUPPLY CONNECTION (Fig.B)
Connect water supply line (1) to faucet Inlet (2). (Supply line
is not included). Please follow manufacturer’s instructions
when installing suppy line.
7 UNIT START UP
Turn on hot and cold water supplies, and check for leaks
above and below the sink.
CAUTION: Maintenance
DISASSEMBLY
1. Replacement parts may be available at the store where you
purchased your faucet.
2. When replacement parts are not available, please write or
call Price Pfister Consumer Service.
3. Always turn off water and relieve pressure before
working on your faucet.
NOTE: Trim Care
Cleaning Instructions:
For all Handles and decorative finishes, use only a soft damp
cloth to clean and shine. Use of polish, detergents, abrasive
cleaners, organic solvents or acid may cause damage. Use of
other than a soft damp cloth will nullify our warranty!
Special Trim:
Trim products which contain Porcelain or other similar
substance are not acceptable for public areas or Commercial
use. Installation of Said Trim is at Users Risk!
8 VALVE FUNCTIONS (Fig.C)
Turning the lever (1) in a clockwise direction will activate the
valve allowing water to flow. Once the lever (1) has rotated
from its original forward position by 90˚ the faucet will have
reached its maximum flow and the lever (1) will turn no
further. To reduce water flow, rotate the lever in a counter-
clockwise direction. The water flow will shut off once the lever
has been rotated back to its original forward position.
9 REPLACEMENT OF THE CARTRIDGE
(Fig.D)
(close the main water supply) Unscrew the set screw (1), take
off the handle (2), and unscrew the cap (3). Using a wrench,
unscrew the cartridge (4) and lift it out of the faucet body
(5). To assemble proceed in reverse order, mind to clean the
surfaces in contact with the sealing washers. Tighten the nut
(4) in such a way that ensures a quality seal while allowing
the handle (2) to turn smoothly.
10 CLEANING THE AERATOR (Fig.E)
It is advisable to periodically clean the aerator, in order to
avoid build-up of dirt and limestone, which in time could
gradually limit the water flow. To disassemble the aerator
(1) , unscrew it and clean the filter (2) from all impurities,
reassemble by proceeding in the reverse order making sure
the gasket (3) is correctly placed.
Supply Suggested Maximum Minimum
Hot Water
Temperature
65 Cº (150ºF) 80 Cº (175ºF) 15 Cº (60ºF)
Operating
Pressure
3 BAR (44PSI) 5 BAR (73PSI) 0.5 BAR (7PSI)
D
B
A
C
E
OPEN
CLOSED