Wiegmann ULTIMATE - Manual (Page 20)

U LT I M AT E E N C L O S U R E A C C E S S O R I E S
S W I N G O U T PA N E L • PA N E L C O N V E R S I O N K I T
J20
F E AT U R E S - S P E C I F I C AT I O N S
www.hubbell-wiegmann.com
Data Subject To Change Without Notice
S W I N G O U T PA N E L
Swing panels are designed to mount internal equipment
directly behind the main enclosure door. Maximum swing
is 107 degrees. Convenient access to sub enclosure is
provided via 1⁄4 turn pull-tab. On solid doors, the clear-
ance from the swing panel face to the interior door face is
1-1⁄4", and 1" on window doors (when the door is closed).
The kit includes the swing panel, brackets and hardware
necessary for a tub flange install. Swing out panels meet
Type 1 with enclosure door open.
Finish: White Polyester Powder.
Note: Swing out panel can also be mounted on front-to-back
adjustable depth mounting kits, or rear panel studs (adjustable
mounting kits must be purchased separately.
PA N E L C O N V E R S I O N K I T
These kits allow you to utilize standard NEMA “NP” (non
Ultimate panels) within Ultimate enclosures. Simply bolt
the conversion brackets over the top of existing studs,
then install the Ultimate sub panel. Kit includes four
adapter plates and hardware for mounting Ultimate sub
panels.
Finish: White Polyester Powder.
S W I N G O U T PA N E L
CATALOG NUMBER
HFWNSP1212C
HFWNSP1612C
HFWNSP1616C
HFWNSP2016C
HFWNSP2416C
HFWNSP1620C
HFWNSP2020C
HFWNSP2420C
HFWNSP3020C
HFWNSP2024C
HFWNSP2424C
HFWNSP3024C
HFWNSP3624C
HFWNSP3030C
HFWNSP3630C
HFWNSP3636C
1 2 X 1 2 ( H X W )
1 6 X 1 2 ( H X W )
1 6 X 1 6 ( H X W )
2 0 X 1 6 ( H X W )
2 4 X 1 6 ( H X W )
1 6 X 2 0 ( H X W )
2 0 X 2 0 ( H X W )
2 4 X 2 0 ( H X W )
3 0 X 2 0 ( H X W )
2 0 X 2 4 ( H X W )
2 4 X 2 4 ( H X W )
3 0 X 2 4 ( H X W )
3 6 X 2 4 ( H X W )
3 0 X 3 0 ( H X W )
3 6 X 3 0 ( H X W )
3 6 X 3 6 ( H X W )
FOR ENCLOSURE SIZE
**Time Saver Note: Tired of all the extensive labor when removing the competitions’ swing panel
to adjust the multi-depth brackets, then re-installing the swing panel? How many times have you
had to adjust because of different depth instruments? Wiegmann has solved the problem!
Simply use the hole access area on the swing panel, loosen the screws and adjust your swing
panel. Once the correct dimension is reached, simply tighten the screw and your ready to go!
PA N E L C O N V E R S I O N K I T
CATALOG NUMBER
HFWCNP4C A n y t h i n g 3 0 H X 3 0 W o r l e s s
FOR ENCLOSURE SIZE