Paasche Airbrush GT-PL - Manual

GT-25
Paint Tank
WARNING: Please read and save these instructions. Read
carefully before attempting to assemble, install, operate or
maintain the product described. Protect yourself and others
by observing all safety information. Failure to comply with
instructions could result in personal injury and/or property
damage! Retain instructions for future reference.
DO NOT PRESSURIzE TANk OVER 60 PSI.
This manual contains information that is very
important to know and understand. This
information is provided for SAFETY and to
PREVENT EQUIPMENT PROBLEMS. To
help recognize this information, observe the
following symbols.
Danger indicates
an
imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
warning indicates
a potentially
hazardous situation which, if not
avoided, CoulD result in death or
serious injury.
INSTRUCTIONS AND PARTS LIST GT-25, 8/31/2011
INSTRUCTIONS AND PARTS LIST GT-25, 10/2007
Caution indicates
a potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
After unpacking the unit, inspect
carefully for any damage that may have
occurred during transit. Make sure to
tighten fittings, bolts, etc., before putting
unit into service.
Do not operate unit
if damaged during
shipping, handling or use. Damage
may result in bursting and cause
injury or property damage.
Since the paint tank and other
components used, (air compressor,
material pump, spray guns, filters,
lubricators, hoses, etc.) make up a high
pressure pumping system, the following
safety precautions must be observed at
all times:
1. Read all manuals included
with this product carefully.
Be thoroughly familiar with
the controls and the proper
use of the equipment.
Printed in the U.S.A.
This paint tank is designed for large
volume projects using spray guns and
paint rollers. The tank is capable of
holding 2.5 gallons of bulk paint or a 1
gallon can of paint may be placed
directly inside the tank.
Basic construction of the unit consists of
a heavy deep drawn one piece steel tank,
die cast aluminum tank lid and eyebolt
clamps. The unit is equipped with a
pressure regulator, gauge, safety relief
valve, material hose and air line
connectors. A convenient carrying handle
allows attachment of the unit to the rung
of a ladder or scaffolding to facilitate
house or barn spraying operations.
2. Follow all local electrical and safety
codes, as well as the National
Electrical Code (NEC) and in the
United States, the Occupational
Safety and Health Act (OSHA).
3. Do not pressurize tank over 60 psi.
4. Do not exceed the pressure rating of
any component in the system.
5. Be certain that pressure regulator
and safety valve are clean and in
proper working order before using
the paint tank.
6. Be certain that the air supply line is
at zero psi and pressure regulator is
turned off before connecting tank to
air supply.
7. Make sure all feed lines, clamps and
spray guns are secure before turning
air supply on.
8. Release all pressure within the
system before attempting to service
any component.
9. Protect material lines and air lines
from damage or puncture.
10. Never point a spray gun at yourself
or at any other person. Accidental
discharge may result in serious
injury.
11. Check hoses for weak or worn
condition before each use, making
certain that all connections are
secure.
Maximum
Tank Tank I.D. Overall Weight Paint hose Working
Capacity Dimensions Dimensions (Empty) Material Pressure
1 Gallon can or 8.5'' Dia. x 11'' 12" x 12 " x 22'' 12 lbs. 60 psi
2.5 Gal. bulk
Paasche Airbrush Company
4311 North Normandy Avenue
Chicago, Illinois 60634-1395
Description
Safety Guidelines
General Safety Information
Unpacking
Website: www.paascheairbrush.com
Phone: 1-800-621-1907
Fax: 1-877-867-9198
Specifications