Luxor|H.Wilson LEM32TT - Manual (Page 2)

Instruction Sheet
Endura Models LEM32K, LEM32TK & LEM32TTK
LEM32K LEM32TK LEM32TTK
PARTS LIST
LEM32K LEM32TK LEM32TTK
IMPORTANT
PULLOUT SHELF ASSEMBLY: CART ASSEMBLY:
The electrical unit & pullout shelf
should be assembled first.
2.
3.
4.
Position bottom shelf with open cut-out facing toward the front, ribbed
side up, over the 4 legs of the top shelf as illustrated. Insert leg posts
into legs. Using a rubber mallet, firmly hammer bottom shelf into legs
until all four legs are seated (flush) against the surfaces of both
shelves.
5.
Push the four casters firmly into the holes in each corner of the bottom
shelf. Important: casters must be fully seated. Tap firmly with rubber mallet
to properly seat casters. Turn your Endura Workstation right side up.
6.
CORD GUIDE COVER
TERMINAL
PLATFORM
GROMMET CAP
CORD GUIDE COVER
MIDDLE SHELF
GROMMET CAP
GROMMET RING
CABLE GROMMET HOLE
GROMMET RING
LEG POST
BACK
LEG
POST
LEG
POST
1.
Install grommet
rings by tapping into
place with rubber
mallet. Snap off cord
guide cover from
grommet cap so
equipment plug may
be run through
grommet to plug
unit, then insert
grommet cap into
grommet ring.
LEM32T / LEM32TT
For LEM32T &
LEM32TT
Tools Required:
Rubber Mallet
Phillips Screwdriver
www.luxorfurn.com
www.hwilson.com
x1 - 24x32 Top Shelf w/
Handle
x4 - 17.5˝ Legs
x1 - 24x32 Bottom Shelf w/
Cutout
x1 - Set of 4˝ Casters
2 w/ Locking Brake
x1 - Electric Assembly
x2 - Cable Clips
x1 - Grommet Cord Guide
x1 - Pullout Shelf Kit
x1 - 24x12 Terminal Platform
x4 - 8˝ Legs
x1 - 24x32 Middle Shelf w/
Handle
x4 - 17.5˝ Legs
x1 - 24x32 Bottom Shelf w/
Cutout
x1 - Set of 4˝ Casters
2 w/ Locking Brake
x1 - Electric Assembly
x2 - Cable Clips
x2 - Grommet Cord Guide
x1 - Pullout Shelf Kit
x1 - 24x12 Terminal Platform
x1 - 24x32 Middle Shelf w/
Handle
x8 - 20˝ Legs
x1 - 24x32 Bottom Shelf w/
Cutout
x1 - Set of 4˝ Casters
2 w/ Locking Brake
x1 - Electric Assembly
x2 - Cable Clips
x2 - Grommet Cord Guide
x1 - Pullout Shelft Kit
1
Firmly seat electrical assembly 3 plug unit into
handle plug housing as illustrated. Secure with
power cord plug retaining bracket. Thread cord
through cord retaining track and out the open-
ing in the side of the handle.
2
Secure power cord management tie into starter
hole with sheet metal screws. See illustration
A. Secure with power cord management tie by
wrapping tie around cord and fastening. Cut off
any unnecessary extra length of tie.
3
Wrap the cord
around the handle.
4
For safety and neat
appearance secure cord
plug to cord by utilizing
plug snap.
CORD
RETAINING
TRACK #2
CORD
RETAINING
TRACK #1
3 PLUG UNIT
POWER CORD PLUG
RETAINING BRACKET
A
CORD MANAGEMENT TIE
POWER CORD
MANAGEMENT TIES
TIE IS IN SECURED
POSITION
2A. To install metal pull-out shelf, first turn workstation top shelf upside down, locate the four “L”
bracket support members as shown in step 1.
2B. Secure “L” brackets to “L” bracket support members using two 5/8 sheet metal screws per
bracket. Do not fully tighten screws at this time. Note: “L” brackets must face each other point-
ing in towards center of workstation shelf.
2C. Next, identify left runner from right runner. This is done by extending runner fully to locate the
three holes used to attach to metal shelf. This portion of the runner with holes must face toward
front of metal shelf. Turn metal shelf upside down and install runners on each side using three
sheet metal screws on each side. Special Note: Remember all assembly is being done upside
down. Position assembled shelf and runner between “L” brackets to determine proper spacing
of “L” brackets. Carefully remove metal shelf and fully tighten “L” brackets.
2D.Use self-tapping screws to secure runner to “L” brackets. For maximum clearance use hole on
“L” bracket that is farthest away from workstation top shelf.
2E.Install grommet ring by tapping into place with rubber mallet. Snap off cord guide cover from
grommet cap so equipment plug may be run through grommet to plug unit, then insert grom-
met cap into grommet ring.
3A. Lay top shelf (with handle) ribbed side up on a smooth surface. Push all 4 legs onto leg posts.
3B.Position bottom shelf with open cut-out facing toward the front, ribbed side up, over the 4 legs
of the top shelf as illustrated. Insert leg posts into legs. Using a rubber mallet, firmly hammer
bottom shelf into legs until all four legs are seated (flush) against the surfaces of both shelves.
3C.Push the four casters firmly into the holes in each corner of the bottom shelf. :
ers must be fully seated. Tap firmly with rubber mallet to properly seat casters. Turn your Endura
workstations right side up. It is now ready to use.
METAL
KEYBOARD
SHELF
Self Tapping Screws
Sheet Metal Screws
(in Runner Bag)
RUNNER
“L” BRACKETS
LOCKING CASTERS
FRONT
Set terminal platform as complet-
ed in Step No. 2 right side up and
set its legs onto leg posts of
middle shelf. Grommet hole should
be to the back of terminal
platform. Firmly hammer terminal
platform with legs onto leg posts of
middle shelf until legs are seated
(flush) against the surface of
middle shelf and terminal
platform. Your Endura Computer
Workstation is now ready for use.
TERMINAL
PLA
TFORM
Lay middle shelf (with handle) ribbed side
up on a smooth surface. Push all 4 long legs
onto leg posts.
Lay terminal platform (long narrow shelf with
grommet hole) ribbed side up on a smooth
surface. Push 1 set of short legs onto leg
posts. Set aside temporarily and continue
with step No. 3.
Upated 10/5/12