Luxor|H.Wilson LEF34 User Manual

Parts list, Lef-34c lef-56c

INSTRUCTION SHEET - Endura Mobile Cabinet Tables

ModelS LEF-34C, LEF-40C, LEF-42C AND LEF-56C

Customer Service Dept

2245 Delany Rd

Waukegan, IL 60087

Ph: 847/244-1800 • 800/323-4656

Fax: 847/244-1818 • 800/327-1698

1 - Top Shelf w/handle

4 - Tubular Legs

1 - Bottom Shelf

2 - Cabinet Side Panels

1 - Back Panel

1 - Door in Frame

4 - Casters ( 2 w/brake)

1 - Grommet Cap

1 - Cord Guide Cover

1 - Grommet Rings

1 - Large “U” Bracket

1 - Cord Wrap Bracket

2 - Machine Screws

2 - Small Kep Nuts

1 - Rubber Band

TOOLS REQUIRED:

1 - Rubber mallet

1 - Slotted screwdriver

1 -

⁄

˝ wrench

PARTS LIST

LEF-34C

LEF-56C

Start by closing the electric

plug housing in the handle of

the top shelf as illustrated.

With bottom shelf facing up push all four legs onto cor-

ner posts. Using rubber mallet hammer legs firmly into

position. Legs must be seated (flush) against the shelf

surface. Place rubber band around legs to aid in the

assembly of side panels and doors.

Install the back panel in the same manner as side pan-

els. Install grommet ring into grommet hole. Insert two

machine screws as illustrated through “U” bracket into

back panel and through slots in cord wrap bracket. Align

the cord wrap bracket onto machine screws from the out-

side of back shelf and secure with two kep nuts.

Press 3-outlet power cord into “U” bracket and feed

remaining cord through grommet hole and wrap

remaining cord around cord wrap bracket. For safety

and neat appearance, secure cord plug to cord with

plug snap.

Install door panel same as back panel with door

handle at top. Be sure door opens outward and

door frame is also placed between legs and nest-

ed flush on the shelf floor.

Push the four casters firmly into the holes in each cor-

ner of the bottom shelf. Important: casters must be

fully seated. Tap firmly with rubber mallet to properly

seat casters. Turn your Endura Table right side up.

Open door and insert exrta shelf onto the shelf

supports on the side panels.

Begin seating of top shelf by holding door panel, leg and

side panel as illustrated. Gently tap corner posts into

legs until all posts are partially inserted into legs. Repeat

hammering action more firmly going around to each cor-

ner, being certain that each panel nests inside the lip of

the top shelf. Repeat this action until top shelf is fully

nested.

Install grommet ring and grommet cap into top shelf.

For tables with electric assembly, snap off cord guide

cover from grommet cap to allow equipment plug entry.

Insert grommet cap into grommet ring.

PLUG

HOUSING

COVER

TOP

SHELF

RUBBER BAND

BOTTOM

SHELF

SIDE

PANEL

TOP VIEW

LEGS

SIDE VIEW WITH PANEL

SEATED INSIDE SHELF LIP

MAKE SURE STUD WELDS ARE

CLOSER TO BOTTOM THAN TOP.

MAKE SURE

TO TAKE KEYS

FROM INSIDE

OF DOOR.

GROMMET HOLE

GROMMET RING

MACHINE

SCREWS

KEP NUT

CORD WRAP BRACKET

“U”

BRACKET

BACK

PANEL

GROMMET

HOLE

“U”

BRACKET

INSIDE

BACK PANEL

CORD WRAP

BRACKET

PLUG SNAP

OUTSIDE

BACK PANEL

NOTE: MODELS LEF-40C AND

LEF-56C HAVE DOUBLE

DOORS

CORD GUIDE

COVER

GROMMET CAP

GROMMET RING

TOP

SHELF

PLACE LOCKING CAST-

ERS AS ILLUSTRATED

Install the side panels first. Slide panels down between

legs until they are nested inside the shelf lip and flush

against the shelf surface. Rubber band will hold legs

and side panels in place while installing back panel and

front door.