Luxor|H.Wilson LE54WT - Manual (Page 3)

Instruction Sheet - Endura Mobile Cabinet Tables
Models LE-34C, LE-40C, LE-42C, LE-48C and LE-54C
Customer Service Department
Luxor
2245 Delany Road
Waukegan, IL 60087
Ph: 847/244-1800 • 800/323-4656
Fax: 847/244-1818 • 800/327-1698
PARTS LIST
Models LE-34C, LE-40C, LE-42C, LE-48C, LE-54C
1 - Top shelf w/handle 1 - Door in frame
1 - Center shelf w/eight leg posts 1 - Grommet cap
1 - bottom shelf w/caster sockets 1 - Cord guide cover
4 - Short legs 1 - Grommet ring
4 - Long legs 1 - Rubber band
2 - Cabinet side panels
1 - Back panel
4 - Casters 2 with brake
Tools Required:
Rubber mallet
IMPORTANT
The electrical unit should
be assembled first .
If your Endura Cabinet
Table does not have the
Electrical Assembly and
Cable-Track™ Cord
Management System,
start by closing the elec-
trical plug housing in the
handle of the top shelf as
illustrated below.
6
Begin seating of center shelf by holding door panel,
leg and side panel as illustrated. Gently tap corner
post into leg. Repeat on all 4 sides until all posts
are partially inserted into legs. Now repeat ham-
mering action more firmly going around to each
shelf post and driving the leg posts more securely
into the legs.
Top of panels and door frame must be nested into
the underside of the center shelf lip in the same
manner as the bottom shelf.
7
Push remaining 4 legs onto center shelf posts as
illustrated. Place top shelf (with handle) onto legs.
Insert leg posts into legs of top shelf. Using rubber
mallet, firmly hammer top shelf into legs until all
four legs are seated against shelf surface. install
grommet ring and grommet cap into top of shelf.
For tables with electric assembly, snap off cord
guide cover form grommet cap to allow equipment
plug to be run through grommet. Insert grommet
cap into grommet ring. Remove rubber band.
2
With bottom shelf facing up push all four 18” legs
onto leg posts. Using rubber mallet hammer legs
firmly into position. Legs must be seated (flush)
against the shelf surface. Place rubber band
around legs to aid in the assembly of cabinet
side panels and doors.
3
Install the side panels first. Slide panels down
between legs until they are nested inside the
shelf lip and flush against the shelf surface.
Rubber band will hold legs and side panels in
place while installing back panel and front door.
4
Install the back panel in the same manner as
shown in Step #3. NOTE: Cabling hole in back
panel should be toward the top.
5
Install door panel same as back panel, with
door handle at top.
8
Push the four casters firmly into the holes in
each corner of the bottom shelf. Important: cast-
ers must be fully seated. Tap firmly with rubber
mallet to properly seat casters. Turn your
Endura Table right side up.
18” LEG
RUBBER BAND
BOTTOM
SHELF
LEG POST
SIDE
PANEL
SIDE VIEW WITH
PANEL SEATED
INSIDE SHELF LIP
LEGS
TOP VIEW NOTE: Models LE-40C, LE-48C, and LE-54C
have double doors.
PLUG
HOUSING
COVER
CENTER
SHELF TOP
SHELF
CORD
GUIDE
COVER
GROMMET CAP
GROMMET RING
CENTER SHELF
PLACE LOCKING CASTERS
AS ILLUSTRATED
FRONT
BACK
LE-54C LE-40C LE-42C
1
Units with electric receive following parts:
1- Cord guide cover
1- Cord wrap
4- Cord ties
1- L-bracket
6- Screws
1- Power cord
Units without electric receive following parts:
1- Cord guide cover
2- Screws
1- Plug housing cover