beautypg.com

Warning – Rivers Edge RE765 Universal Concealment Curtain User Manual

Page 4

background image

TREESTANDS

Universal Concealment Curtain (RE765)

Page 4

HuntRiversEdge.com

HuntRiversEdge.com

800-450-EDGE (3343)

waRninG

THiS CURTain iS MaDE wiTH a HEaVY SPRinG
STEEL FRaME THaT SPRinGS OPEn DURinG SET-
UP. USE CaUTiOn wHEn SETTinG UP. KEEP awaY
FROM BODY anD FaCE. KEEP CLEaR OF OTHER
PEOPLE wHiLE SETTinG UP.
DO nOT aLLOw EXCESSiVE STRaP BUiLDUP in
RaTCHET aS THiS wiLL PREVEnT THE RaTCHET
TEETH FROM EnGaGinG CaUSinG SLiPPaGE.
aLwaYS aTTaCH RaTCHET STRaP SECURELY
wHiLE USinG THiS PRODUCT!
BE SURE BOTH SiDES OF RaiL aSSEMBLY aRE
SEaTED COMPLETELY TOGETHER On TREE MOUnT
STUDS DURinG USE.
nEVER LEan aGainST, LEan OVER OR SiT On
SHOOTinG RaiL. iT iS DESiGnED aS a SHOOTinG
REST OnLY. aLwaYS BE awaRE THaT THE SHOOT-
inG RaiL Can SwinG TO OnE SiDE OR THE OTHER.
BE SURE SHOOTinG RaiL iS SET OFF TO THE SiDE
(On OnE STUD) wHEn EnTERinG OR EXiTinG
YOUR STanD.
STUDY YOUR nEw PRODUCT TO BECOME FaMiL-
iaR wiTH aLL OF iTS FEaTURES anD DESiGn. aT
GROUnD LEVEL, FOLLOwinG PROViDED SETUP
& USE inSTRUCTiOnS, PRaCTiCE aTTaCHinG TO
TREE anD REMOVinG FROM TREE. PRaCTiCE
SiTTinG, STanDinG, anD USinG THiS PRODUCT
BEFORE aTTaCHinG OVERHEaD. SaVE THESE in-
STRUCTiOnS FOR FUTURE REFEREnCE.
nEVER aTTaCH TO a DEaD, ODD-SHaPED, LEan-
inG, DiSEaSED, LOOSE-BaRKED TREE OR UTiL-
iTY POLES.
BRinG RaTCHET STRaP UP wiTH YOU in a POCK-
ET- DO nOT CaRRY in YOUR HanDS!
YOU MUST aLwaYS aTTaCH YOUR FULL BODY
HaRnESS (FaLL aRREST SYSTEM) TETHER TO
THE TREE BEFORE SECURinG COnCEaLMEnT
CURTain COMPOnEnTS TO THE TREE.
nEVER LEaVE THE COnCEaLMEnT CURTain FRaME
aTTaCHED TO TREE wiTH CaMO CURTain aTTaCHED,
DaMaGE FROM winD wiLL OCCUR. iF COnCEaL-
MEnT CURTain FRaME wiLL BE LEFT On THE TREE
wHiLE nOT HUnTinG, aLwaYS REMOVE THE CaMO
CURTain SO DaMaGE DOES nOT OCCUR.

4. For safe entry/exit from your treestand while using the Universal

Concealment Curtain, release the necessary side release buckles
on the lower portion of curtain from the treestand. Lift either side
of the rail assembly off the stud and pivot rail frame away for
unrestricted access to your climbing aid or ladder. It is recommended
that you always remove the concealment curtain from the rail
assembly after use and store away in the provided carrying bag to
help prevent unnecessary damage or fading to the material.

5. reverse setup and use instructions to remove Concealment Curtain

frame from tree. To fold up curtain, fold each outer panel over the
center panel to create one flat panel. Grasp the folded curtain from
opposite sides and twist your hands in opposite directions of each
other. This action will make the blind fold down into a smaller circle
so it will fit back into the carrying bag.

inSPECTiOn anD MainTEnanCE SCHEDULE
FOR aLL RiVERS EDGE PRODUCTS

• Inspect all webbing, rope, cord, and strap assemblies for wear or

damage.

• Inspect cables and cable ends for damage or kinking.
• Inspect all hardware and chain components for damage.
• Inspect for any structural damage to product. (return to factory for

repair or discard product if any damage is found.)

• Inspect all nut and bolt assemblies to be certain none are loose.
• Inspect for any missing parts.
• Lubricate all pivot and slide together points with powder graphite to

prevent noise, wear, and rust.

• Inspect entire product for any rust, corrosion, cracks, freezing,

excessive heat or rotting damage that may effect the safety of your
product. Discard any questionable product.

• Inspect entire product for any structural damage - pay close attention

to all weld locations. (return to factory for repair or discard product
if any damage is found.)

• Using correct wrenches inspect all nut & bolt assembly locations

and snug up any that may be loose. Be careful not to crush tubing
when tightening!

• Inspect and check operation of all cables, cable ends, cord, rope,

webbing, and strap or chain assemblies. replace with factory new
any item or assembly that shows signs of wear, damage, kinking,
or functions incorrectly.

• Inspect seat. replace any seat with factory new that shows signs

of structural damage or wear.

• Inspect all hardware for wear or damage, also be sure you have no

missing parts.

• Never modify your stand in any way by making repairs, replacing

parts, or altering adding or attaching anything to it except if explicitly
authorized in writing by the manufacturer.