Farm Star HK-308 - Manual (Page 11)

1 10
To the Owner/Operator/Dealer
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded opera-
tor who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this
implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!!
Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT
SAFETY WARNING MESSAGES. CAREFULLY READ EACH
WARNING MESSAGE THAT FOLLOWS. FAILURE TO
UNDERSTAND AND OBEY A SAFETY WARNING, OR
RECOGNIZE A SAFETY HAZARD, COULD RESULT IN AN
INJURY OR DEATH TO YOU OR OTHERS AROUND YOU.
THE OPERATOR IS ULTIMATELY RESPONSIBLE FOR THE
SAFETY OF HIMSELF, AS WELL AS OTHERS, IN THE
OPERATING AREA OF THE TRACTOR AND EQUIPMENT.
UNDERSTAND SIGNAL WORDS
Note the use of the signal words DANGER, WARNING
and CAUTION with the safety messages. The
appropriate signal word for each has been selected
using the following guidelines:
DANGER: Indicates an imminently hazardous situation
that, if not avoided, will result in death or serious injury.
This signal word is to be limited to the most extreme
situations typically for machine components which, for
functional purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous sit-
uation that, if not avoided, could result in death
or serious injury, and includes hazards that are
exposed when guards are removed. It may also
be used to alert against unsafe practices.
CAUTION: Indicates a potentially hazardous sit-
uation that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
THIS SYMBOL MEANS
– ATTENTION!
– BECOME ALERT!
– YOUR SAFETY IS INVOLVED!
I M P O RTA N T S A F E T Y I N F O R M ATION!
Working with unfamiliar equipment can lead to careless injuries. Read this manual, and the manual for your tractor,
before assembly or operating, to acquaint yourself with the machine. It is the equipment owner’s responsibility, if this
equipment is used by any person other than yourself, is loaned or rented, to make certain that the operator, prior to
operating:
1. Reads and understands the operator’s manuals.
2. Is instructed in safe and proper use.
The use of this equipment is subject to certain hazards which cannot be protected against by mechanical
means or product design. All operators of this equipment must read and understand this entire manual, paying
particular attention to safety and operating instructions, prior to using. If there is something in this manual you
do not understand, ask your supervisor, or your dealer, to explain it to you.
Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders twenty-five feet (25’)
from operating equipment. Only properly trained people should operate this tractor and attached implement. It
is recommended the tractor be equipped with a Roll-Over Protection System (ROPS) and a seat belt that is used.
Always stop the tractor, set brake, shut off the tractor engine, remove the tractor key, and lower implement to the
ground before dismounting tractor. Never leave equipment unattended with the tractor running.
R E PAIR PA RTS LIST
FOR HK-308
REF. PART NO.
NO. NO. DESCRIPTION REQ’D.
1 862801 Rocker Shaft Assembly 1
2 862805 Rocker Shaft Mount-LH 1
3 862821 Rocker Shaft Mount-RH 1
4 862808 Mount-Base Assembly 1
5 862814 Lift Arm Assembly 2
6 862817 Hydraulic Cylinder (1 3 / 4 ” x 6”) 1
7 862818 Hydraulic Hose 1
8 590001 Cat. I Toplink Pin (AK-8) 1
9 590006 Linch Pin (AK-14) 3
10 2503007 Bolt 1 / 2 ” – 13 NC x 2” Hex Head 2
11 2502002 Spring Lock Washer 1 / 2 ” 4
12 2500003 Nut 1 / 2 ” – 13 NC Full Hex 4
13 2503165 Bolt 1 / 2 ” – 13 NC x 2 1 / 2 ” (Carriage Head) 2
14 590125 Cat. O Toplink (AK-300) 2
15 2500050 Nut 1 / 2 ” – 13 NC Jam Nylock 1
16 2503051 Bolt 5 / 8 ” – 11 NC x 2 1 / 2 ” Hex Head 6
17 2502007 Spring Lock Washer 5 / 8 ” 6
18 2501005 Flat Washer 5 / 8 ” 6
19 2500013 Nut 5 / 8 ” – 11 NC Full Hex 6
20 2503023 Bolt 3 / 4 ” – 10 NC x 4” Hex Head 1
21 2500037 Nut 3 / 4 ” – 10 NC Hex Nylock 1
22 2503081 Bolt 1 / 2 ” – 13 NC x 2 1 / 4 ” Hex Head 1
23 590277 Toplink Barrel 1
24 590024 R.H. Repair End (AK-49) 1
25 590023 L.H. Repair End (AK-48) 1
26 590145 Knock-In Handle 1
27 2500020 Nut 1” – 8 NC Hex Jam 1
28 862827 Stabilizer Bar 2
29 2503010 Bolt 7 / 16 ” – 14 NC x 1” (Carriage Head) 2
30 2502006 Spring Lock Washer 7 / 16 ” 2
31 2500012 Nut 7 / 16 ” – 14 NC Full Hex 2
N.S. 101039 Safety Sign (Caution) 1
N.S. 101082 Safety Sign (Warning) 1