Blagdon Pump B50 W1 User Manual
Page 4
TECHNICAL DATA
FLUID CONNECTIONS
CAPACITY
MAX SOLIDS
MAX DISCHARGE HEAD
DISPLACEMENT/STROKE
2” BSP (F)
0 - 250 Litres/Minute
(0 - 55 Gallons/Minute)
6 MM
(1/4”)
88 Meters
(289 ft)
1.9 Litres
(0.42 UK Gallons)
MAX. WORKING PRESSURE
AIR INLET
TEMPERATURE LIMITS
PUMP WEIGHTS :-
10 Bar (145 psi)
3/4” BSP (F)
Determined by Elastomers
AA :- 35 Kg
CC:-70 Kg
CA :- 50 Kg
Note ! Maximum discharge pressure must not exceed 10 bar.
Caution -
Operating temperature limitations are as follows:
Operating Temperatures
Materials
Maximum
Minimum
Optimum
Buna-n -
General purpose, oil resistant. Shows good solvent, oil, water and hydraulic fluid resistance. Should not
be used with highly polar solvents like acetone and MEK, ozone, chlorinated hydrocarbons and nitro hydrocarbons.
176
o
F
80
o
C
-18
o
F
-28
o
C
50
o
to 140
o
F
10
o
to 60
o
C
EPDM -
Shows very good water and chemical resistance. Has poor resistance to oils and solvents, but is fair on
ketones and alcohols.
212
o
F
100
o
C
-11
o
F
-24
o
C
50
o
to 212
o
F
10
o
to 100
o
C
Neoprene -
All purpose. Resistant to vegetable oil. Generally not affected by moderate chemicals, fats greases
and many oils and solvents. Generally attacked by strong oxidising acids, ketones, esters, nitro hydro carbons and
chlorinated aromatic hydrocarbons.
212
o
F
100
o
C
-4
o
F
-20
o
C
50
o
to 130
o
F
10
o
to 54
o
C
Santoprene® -
Injection moulded thermoplastic elastomer with no fabric layer. Long mechanical flex life.
Excellent abrasion resistance.
212
o
F
100
o
C
-10
o
F
-23
o
C
50
o
to 212
o
F
10
o
to 100
o
C
PTFE -
Chemically inert, virtually impervious. Very few chemicals are known to react chemically with PTFE :
molten alkali metals, turbulent liquid or gaseous fluorine and a few fluoro-chemicals such as chlorine trifluoride or
oxygen difluoride which readily liberate free fluorine at elevated temperatures.
356
o
F
180
o
C
32
o
F
0
o
C
50
o
to 212
o
F
10
o
to 100
o
C
Viton® -
Shows good resistance to a wide range of oils and solvents : especially all alphatic, aromatic and
halogenated hydrocarbons, acids, animal and vegetable oils.
356
o
F
180
o
C
0
o
F
-18
o
C
75
o
to 212
o
F
24
o
to 100
o
C
Polypropylene -
High strength, light weight, corrosion resistant polyolefin which easily withstands most
chemicals, with no known solvent at room temperature.
158
o
F
70
o
C
-40
o
F
-40
o
C
50
o
to 140
o
F
10
o
to 60
o
C
MODEL - B50
WETTED COMPONENTS
A : ALUMINIUM
C: CAST IRON
NON - WETTED COMPONENTS
A : ALUMINIUM
C : CAST IRON
VALVE TYPE
B : BALL
W : WEIGHTED BALL
SUCTION ORIENTATION
B : BOTTOM SUCTION, W1 SERIES
VALVE SEATS
A : ALUMINIUM
S : 316 STAINLESS STEEL
VALVE BALLS
B : BUNA-N
T : PTFE
E : EPDM
V : VITON
N : NEOPRENE
S : ST. STEEL
D : DELRIN (ACETAL)
DIAPHRAGMS
B : BUNA-N
T : PTFE
E : EPDM
V : VITON
H : POLYESTER (HYTREL)
N : NEOPRENE
P : POLYURETHANE
R : SANTOPRENE
O : ONE-PIECE PTFE
DESIGN LEVEL
TYPICAL CODE =
B50 05 A A. W 1. N N S
IDEX Pump Technologies (Ireland) Ltd.,
A Unit of IDEX Corporation,
R79, Shannon, Co Clare, IRELAND.
TEL. : +353 61 471933 FAX. : +353 61 475046
Web Site : www.blagdonpump.com
E-Mail : [email protected]
IMPORTANT
This pump should be used in accordance with the requirements of the Safety, Health & Welfare at Work Act 2005.
All business conducted subject to IDEX Pump Technologies, Ireland. Terms and Conditions of Sale, available on request.
HG-CF-1109 Rev. D – 03.11.11
Page 4