Nova-Tech LMI Roytronic Excel Series AD Metering Pump - Manual (Page 10)

10
INSTALLATION
3.3 Tubing Connections
,QVHUW WXELQJ WKURXJK &RXSOLQJ 1XW²7XELQJ VKRXOG HQWHU WKH VPDOOHU HQG RI WKH &RXSOLQJ 1XW ¿UVW RULHQWLQJ
the larger opening of the Coupling Nut toward the tubing end.
2a. For 1/4” OD tubing: Position the Female Ferrule so that 1/4” to 3/8” (5-10 mm) of tubing protrudes from
the Female Ferrule. Orient the raised collar of the Ferrule toward the Coupling Nut (reference FIGURE 1).
2b. For 3/8” or 1/2” OD tubing: Position a Female Ferrule about one inch (25 mm) from end of tubing. Orient the
UDLVHG FROODU RI WKH )HPDOH )HUUXOH WRZDUG WKH &RXSOLQJ 1XW 7KHQ LQVHUW WKH 0DOH )HUUXOH RQWR WKH HQG RI WKH
WXEH SXVKLQJ WKH WXEH LQWR WKH ERWWRP RI WKH JURRYH LQ WKH 0DOH )HUUXOH 7KHQ VOLGH WKH )HPDOH )HUUXOH GRZQ
WKH WXELQJ DQG ZLWK \RXU ¿QJHUV SUHVV WLJKWO\ LQWR WKH 0DOH )HUUXOH UHIHUHQFH ),*85(
)LUPO\ KDQG WLJKWHQ WKH &RXSOLQJ 1XW RQWR WKH ¿WWLQJ 1RWH 7LJKWHQLQJ ZLWK SOLHUV PD\ FDXVH WKH )HUUXOHV
to break.
A. 86( 21/< /0, 78%,1*²$/:$<6 XVH /0, VXSSOLHG WXELQJ ZLWK \RXU SXPS DV WKH WXELQJ LV VSHFL¿FDOO\
GHVLJQHG IRU XVH ZLWK WKH SXPS ¿WWLQJV
%
DO NOT USE CLEAR VINYL TUBING ON THE DISCHARGE SIDE OF THE PUMP. The pressure created
E\ WKH SXPS FDQ UXSWXUH YLQ\O WXELQJ
& %HIRUH LQVWDOODWLRQ DOO WXELQJ PXVW EH FXW ZLWK D FOHDQ VTXDUH HQG
' 9DOYH DQG KHDG FRQQHFWLRQV IURP WKH IDFWRU\ DUH FDSSHG RU SOXJJHG WR UHWDLQ SUHSULPH ZDWHU 5HPRYH DQG
discard these caps or plugs before connecting tubing.
DO NOT USE PLIERS OR PIPE WRENCH ON COUPLING NUTS OR FITTINGS.
DO NOT REUSE FERRULES—USE ONLY NEW FERRULES.
(5-10 mm)
1/4" - 3/8"
1/4" O.D. or
3x6mm Tubing
Ferrule-
Female
Coupling Nut
Fitting
O-Ring
3/8" O.D. or
6x8mm Tubing
1/2" O.D. or
9x12mm Tubing
Ferrule-
Female
Coupling Nut
Fitting
O-Ring
Ferrule-
Male
FIGURE 1 FIGURE 2
Replacement Ferrules,
and Coupling Nuts
are available as
the following kit
numbers:
¼” Tube – 77382
3 ⁄ 8 ” Tube – 77383
½” Tube – 77384
3 x 6 mm Tube – 77378
6 x 8 mm Tube – 77379
9 x 12 mm Tube – 77380
One kit is needed
for each end of
the tube.