Level Mount DC65ADLP - Manual (Page 4)

4
www.levelmount.com
1-888-229-1459
EU: +0044 844 567 2657
UK: 0844 567 2657
©2011 Level Mount - Patents Pending
These TV Wall Mounts were designed specifically to hold TVs with a maximum weight of up to 200
lbs (90kg) and with the following dimensions: 37” - 85” (939,8 mm - 2159 mm) HE800T, HE885T
and 26” - 85” (660,4 mm - 2159 mm) NTPFW, LMPFW85, DC65ADLP, LM65ADLP, ELPFW-07,
HETWF. Using this product with a TV heavier than the maximum weight, or that exceeds these
dimensions, may result in serious personal injury and damage to equipment and property.
! CAUTION!
Getting Started
1. Do not begin the installation of the TV Wall Mount until you have read and understood the instructions and warnings
contained in these Installation Instructions. Failure to read, thoroughly understand and follow the instructions can
result in serious personal injury and damage to equipment and property. It is the installer’s responsibility to make
sure all components are properly assembled and installed using the instructions provided.
2. If you have questions that do not appear to be covered in these Installation Instructions, please refer to the “Helpful
Hints” section of the detail page for the TV Wall Mount or contact us as described under the “Need Help” section.
If you are at all unsure about any step in these instructions or your ability to install the TV Wall Mount safely and
securely, you should seek professional help from a qualified contractor.
3. This TV Wall Mount contains small items that could be a hazard if swallowed. Keep these items away from
children.
4. The TV Wall Mount must be attached to wood studs or to properly installed anchors in concrete. Do not install the
TV Wall Mount only to drywall or plasterboard. If mounting to wood studs, make sure that mounting screws are
anchored into the center of the studs. See Stud Finder Instructions, included below. Do not use the TV Wall Mount
for devices other than as specified in these instructions.
5. Make sure all screws and bolts are tightened before allowing the TV Wall Mount to bear the full weight of the TV.
Tighten screws and bolts firmly but do not over-tighten them. Once the screw is flush against the TV and the
screwdriver is more difficult to turn and will not turn further, stop; otherwise there is a risk of over-tightening the
bolt. Over-tightening the screws or bolts could damage the TV Wall Mount, greatly reducing its holding power.
Periodic tightening may be required.
6. Screws should easily and completely thread into the TV mounting holes. If any of the screws provided are not
suitable for the TV Wall Mount system, the installer must not under any circumstances drill holes into the TV or into
the TV Wall Mount components. Using screws of improper size can damage the TV.
7. Do not lift more weight than you can handle. Use at least two people when lifting and positioning the TV on the TV
Wall Mount.
8. Before installing, check to make sure all parts of the TV Wall Mount indicated in these Installation Instructions
are included and undamaged. Never use damaged parts or try to install the TV Wall Mount if you do not have all
needed parts.
9. It is the installer’s responsibility to select the appropriate installation location and the supporting surface on which
to mount this TV Wall Mount and to ensure that the TV Wall Mount is anchored properly to the wall. It is also the
installer’s responsibility to ensure that the TV is properly and securely attached to the TV Wall Mount using only the
enclosed fasteners and components and to verify that the screws and power cords do not touch wires, pipes, or
metal parts within the wall (since this could cause damage to these items or cause electrical shock).
10. Level Mount has made every effort to make these Installation Instructions accurate and complete. However,
Level Mount makes no claim that the information contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection with the installation, assembly or use of this product.
Level Mount makes no representation or warranty, express or implied, regarding the accuracy, completeness or
sufficiency of the information contained in this document. Level Mount is not responsible for any damage or injury
caused by incorrect mounting, assembly, installation or use.
25
www.levelmount.com
1-888-229-1459
EU: +0044 844 567 2657
UK: 0844 567 2657
©2011 Level Mount - Patents Pending
Imagen 18
Imagen 17
Imagen 20
Imagen 19
Brazo fijo o
giratorio
bloqueado
Placa de soporte Placa de soporte
Pegado a la Pegado a la
Pared Pared
Brazos fijos o Brazos fijos o giratorio en la pared en la pared
posterior de la televisión posterior de la televisión
Bloqueo
Placa de soporte
Brazos Brazos giratorio
Brazos Brazos
giratorio
Llave Allen
Placa de Placa de
soporte
soporte
I
o
o
TV TV TV
Ima
Llave Allen
Tornillo Allen Allen
Montaje/Instalación
Paso 5 – Montar el televisor de pantalla plana en la placa
de soporte
Antes de montar el televisor de pantalla plana en la Placa de soporte (previamente
fijada a la pared, tal y como se especifica más arriba), primero deberá desbloquear
los brazos fijos o giratorios (que estarán ahora fijos sobre el televisor de pantalla
plana). Para desbloquear los brazos fijos o giratorios, tire de la cuerda hacia arriba,
tal y como muestra la Imagen 17.
Para montar el televisor de pantalla plana en la Placa de soporte, necesitará que 2
personas levanten el televisor de pantalla plana con los brazos fijos o giratorios y los
brazos de extensión, en su caso. Deslice los ganchos de los brazos fijos o giratorios
por encima de la pestaña superior de la Placa de soporte y bájelos hasta que los
brazos fijos o giratorios queden firmemente apoyados a ambos lados de la pestaña
de la Placa de soporte, tal y como muestran las Imágenes 18. Los brazos fijos o
giratorios deben quedar a ras de la Placa de soporte.
Bloquee los Brazos por debajo de la pestaña de la Placa de soporte tirando de
la cuerda, tal y como muestran las Imágenes 17 y 18. Haga lo mismo con el otro
brazo fijo.
Paso 7 – Usar el modo giratorio
(Sólo HETWF, HE800T & HE885T)
Para utilizar la función giratoria o voladiza del brazo, agarre suavemente el televisor
y tire hacia delante de él. El soporte de pared voladizo para televisor se extiende
hasta salir unos 15° de la pared. Después, mueva el televisor hacia arriba o hacia
abajo, tal y como indica la Imagen 20.
Brazo fijo o
giratorio
desbloqueado
Paso 6-Bloqueo de la TV en el soporte de pared (opcional)
(Sólo HETWF, HE800T & HE885T)
Opcional: Para bloquear el televisor a la placa de pared, inserte un candado en el
pestillo de bloqueo como se muestra en la Figura 19. Esto evitará que el televisor se
despegó de la placa de pared.
Nota: El bloqueo no está incluido.
Bloqueo
Placa de so Placa de so