intimus 702 - Manual (Page 4)

CONTROLS:
1 = Pushbutton switch „ready“ (fig. 1)
Depress this switch to start the machine or
to stop the machine.
2 = Light barrier (forward operation) (fig. 2)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
3 = Pushbutton switch „reverse“ (fig. 1)
Pressing this button activates the cutting
mechanism into reverse.
4 = Pilot lamp (fig. 1)
a) „ready“
Continously lights when the pushbutton
switch (1) is operated.
b) „motor protection“
Flashes when the motor is overloaded.
While the motor is cooling down, the ma-
chine cannot be switched on to „forward“
run.
5 = Pilot lamp (fig. 1)
a) „receptacle full“
Flashes when the receptacle is full and
needs to be emptied. At the same time
the machine switches off automatically.
b) „door open“
Continously lights when the door is not
closed. The machine then switches off
automatically and it cannot be started as
long as the door is open.
6 = Pilot lamp „paper jam“ (fig. 1)
Lights when too much paper is fed to the
cutters. The cutting system blocks and stops.
The motor is switched off.
FEEDING OF SINGLE SHEETS:
- Turn machine on with pushbutton switch (1)
(fig. 1). Pilot lamp lights up (4) (fig. 1).
- Feed paper through the inlet guide to the cutting
system.
- Machine switches automatically to forward
and draws paper in. The machine switches off
automatically after shredding.
FEEDING OF COMPUTER PAPER (007SX):
- Fold up the paper tray and place a stack of
computer paper onto it.
The paper tray may not be used as
a step ladder or as a seat. Danger of
tipping over!
- Turn machine on with pushbutton switch (1)
(fig. 1). Pilot lamp lights up (4) (fig. 1).
- Insert the paper underneath the guide rail (7)
(fig. 3) and feed it through the inlet guide to the
cutting system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
Note: In order to always obtain a correct cutting
result in terms of particle size and thus achieve
the safety class according to DIN 32757 as
stated in the brochure, the material to be cut
must always be fed into the cutting mechanism
at a right angle to the cutting mechanism and in
appropriate quantities in the middle of the inlet
slot.
Never feed the shredder with a quantity
of paper exceeding the maximum indi-
cated in the technical details.
Should the machine be overfed, follow the
instructions under „PAPER JAM“.
SCOPE OF APPLICATION:
The document shredder
intimus 702 / 007SX is
a machine for the destruction of common written
material.
The machine may only be used to
shred paper!
Shredding of other types of data carriers
and also of staples and paper clips with
the models with cutting width 0.8x12
mm (007SX) or 0.8x4.5 mm may lead to
injuries (for example due to splintering of
hard materials etc.) and damage to the
machine (for example destruction of the
cutter etc.).
Exception: Single CD’s or 3.5” computer dis-
kettes can also be shredded with
3,8mm, 5,8mm,
4x46mm, 1,9x15mm models.
INSTALLATION:
- Unpack and set machine upright.
- Place plastic sack into the receptacle.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA“.
The air vents in the housing are ne-
cessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
IMPORTANT SAFETY NOTES
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
4
OPERATION
INITIATION
fig. 1
GB
4 6 1 3 5
fig. 3
7
fig. 2
2
702 007SX
OPERATION