American DJ Fire Bowl - Manual (Page 2)

• Be sure that the local power outlet match that of the required voltage
for your unit.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
• Do not remove the fan cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture.
• This unit is intended for indoor use only, use of this product outdoors
voids all warranties.
• During long periods of non use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-Cord Protection - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the fixture.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer.
• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
Fire Bowl™ Safety Precautions
Unit Preparation:
Before beginning initial setup of your Fire Bowl,™ make sure there is
no evident damage caused during transportation. In the event that the
unit’s housing or cable is damaged, do not plug the unit in and do not
attempt to use. Please contact customer support for assistance.
1. Remove all packing materials from the Fire Bowl.™
2. Place the Fire Bowl™ on a flat level surface or suspend the unit
from the ceiling using the included hanging hardware.
3. Plug the power cord into a grounded electrical outlet with a match-
ing power supply.
4. Locate the power switch on the top inner cover of the unit. To turn
the unit on, flip the switch to the “I” position.
Lamps:
The positioning of the lamps is pre-set and does not require any type of
adjustment. Improperly positioned lamps will create deep spots of color
in the flame. Should the lamps need adjustment due shifting during
transit or after the replacement of a lamp, the lamps may be angled
slightly to overcome any heavy color wash. Should the lamps position-
ing become incorrectly, adjust them as follows:
1. To properly position the lamp the unit must be on. Use an insulated
screwdriver to make any adjustment to the lamps position.
2. The amber lamps should be angled to focused on the lower half of
the silk drape.
3. Position the blue lamp to shine directly in the center of silk drape.
4. All lamps will eventually fade or fail. Replacements lamps are
available from your dealer.
Silk Flame:
Your silk flame has been specially designed and hand cut from fine silk
to interact with the airflow and lights to create the illusion of a flame.
Each silk drape is applied prior to shipment and should be in the correct
position. The silk drape has a life of approximately one month when
used continuously in a clean environment. Additional silk drapes may be
purchased through your dealer (part number Z-FLAMEBOWL/SILK).
Fire Bowl™ Set-Up/Operation
© American DJ Supply ® - www.americandj.com - Fire Bowl™ Instruction Manual Page 4 © American DJ Supply ® - www.americandj.com - Fire Bowl™ Instruction Manual Page 3
Fire Bowl™ Halogen Lamp Warning
This fixture is fitted with halogen lamps which are highly susceptible
to damage if improperly handled. Never touch the lamps with your
bare fingers as the oil from your hands will shorten lamp life. Also,
never move the fixture until the lamps have had ample time to cool.
Remember, lamps are not covered under warranty conditions.