Asus MOTHERBOARD si r2.0 - Manual (Page 57)

Chapter 2: BIOS information 2-19
Serial Port Configuration
The sub-items in this menu allow you to set the serial port configuration.
Serial Port [Enabled]
Allows you to enable or disable the serial port (COM).
Configuration options: [Enabled] [Disabled]
Change Settings [IO=3F8h; IRQ=4]
Allows you to select the Serial Port base address . Configuration options: [IO=3F8h;
IRQ=4] [IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3] IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3] ] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3] IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3] ] [IO=2E8h; IRQ=3] IO=2E8h; IRQ=3]]
Parallel Port Configuration
The sub-items in this menu allow you to set the parallel port configuration.
Parallel Port [Enabled]
Allows you to enable or disable the parallel port (LPT).
Configuration options: [Enabled] [Disabled]
Change Settings [Auto]
Allows you to select the Parallel Port base address . Configuration options: [Auto]
[IO=378h; IRQ=5] [IO=378h; IRQ=5,6,7,9,10,11,12] [IO=278h; IRQ=5,6,7,9,10,11,12] IO=378h; IRQ=5,6,7,9,10,11,12] [IO=278h; IRQ=5,6,7,9,10,11,12] ] [IO=278h; IRQ=5,6,7,9,10,11,12] IO=278h; IRQ=5,6,7,9,10,11,12]]
[IO=3BCh; IRQ= 5,6,7,9,10,11,12] IO=3BCh; IRQ= 5,6,7,9,10,11,12]]
Device Mode [STD Printer Mode]
Allows you to change the printer port mode. Configuration options: [STD Printer Mode]
[SPP Mode] [EPP-1.9 and SPP Mode] [EPP-1.7 and SPP Mode] [ECP Mode] [ECP and
EPP 1.9 Mode] [ECP and EPP 1.7 Mode]
2.5.8 APM
Restore AC Power Loss [Power Off]
[Power On] The system goes into on state after an AC power loss.
[Power Off] The system goes into off state after an AC power loss.
[Last State] The system goes into either off or on state, whatever the system state was
before the AC power loss.
Power On By PS/2 Keyboard [Disabled]
[Disabled] Disables the Power On by a PS/2 keyboard.
[Space Bar] Sets the Space Bar on the PS/2 keyboard to turn on the system.
[Ctrl-Esc] Sets the Ctrl+Esc key on the PS/2 keyboard to turn on the system.
[Power Key] Sets Power key on the PS/2 keyboard to turn on the system. This feature
requires an ATX power supply that provides at least 1A on the +5VSB lead.
Power On By PCI [Disabled]
[Disabled] Disables the PCI devices to generate a wake event.
[Enabled] Enables the PCI devices to generate a wake event.
Power On By PCIE [Disabled]
[Disabled] Disables the PCIE devices to generate a wake event.
[Enabled] Enables the PCIE devices to generate a wake event.
E7361_P8H61-M2-TPM-SI R2.0_Manua19 19 5/16/12 1:45:04 PM