beautypg.com

Sata 3.0gb/s connectors, 25 chapter 1: product introduction, Aafp – Asus MOTHERBOARD si r2.0 User Manual

Page 35: You must install windows, Vista / windows, Please use ide mode on windows

background image

1-25

Chapter 1: Product introduction

6.

Serial ATA 3.0 Gb/s connectors (7-pin SATA3G_1-4)
These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical drives via

Serial ATA 3.0 Gb/s signal cables.

7.

Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports

either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel

audio I/O module cable to this connector.

• We recommend that you connect a high-definition front panel audio module to this

connector to avail of the motherboard’s high-definition audio capability.

• If you want to connect a high-definition front panel audio module to this connector, set

the Front Panel Type item in the BIOS setup to [HD]. If you want to connect an AC'97

front panel audio module to this connector, set the item to [AC97]. By default, this

connector is set to [HD]. See section 2.5.7 Onboard Devices Configuration for details.

SATA3G_1

SATA3G_3

SATA3G_2

SATA3G_4

P8H61-M2/TPM/SI R2.0

P8H61-M2/TPM/SI R2.0 Intel

®

SATA 3.0Gb/s connectors

GND

RSATA_TXP3

RSATA_TXN3

GND

RSATA_RXN3

RSATA_RXP3

GND

GND

RSATA_RXP4

RSATA_RXN4

GND

RSATA_TXN4

RSATA_TXP4

GND

GND

RSATA_TXP1

RSATA_TXN1

GND

RSATA_RXN1

RSATA_RXP1

GND

GND

RSATA_RXP2

RSATA_RXN2

GND

RSATA_TXN2

RSATA_TXP2

GND

P8H61-M2/TPM/SI R2.0

P8H61-M2/TPM/SI R2.0 Front panel audio connector

AAFP

AGND

NC

SENSE1_RETUR

SENSE2_RETUR

PORT1 L

PORT1 R

PORT2 R

SENSE_SEND

PORT2 L

HD-audio-compliant

pin definition

PIN 1

AGND

NC

NC

NC

MIC2

MICPWR

Line out_R

NC

Line out_L

Legacy AC’97

compliant definition

• You must install Windows

®

XP Service Pack 3 or later version before using Serial ATA

hard disk drives.

• Due to H61 Chipset limitation, AHCI Mode only works on Windows

®

Vista / Windows

®

7.

Please use IDE Mode on Windows

®

XP.

• [IDE] is the default SATA type. Under Windows

®

XP, there is no need to change the

SATA type.

• To configure the SATA type in BIOS, click Advanced Mode > Advanced tab > SATA

Configuration > SATA Mode Selection.

• When using hot-plug and NCQ on Windows

®

Vista / Windows

®

7, set the SATA Mode

Selection item in the BIOS to [AHCI]. See section 2.5.4 SATA Configuration for details.

E7361_P8H61-M2-TPM-SI R2.0_Manua25 25

5/16/12 1:44:30 PM

This manual is related to the following products: