BVA Hydraulics HL10002 - Manual (Page 2)

2
Figure 1 - Low Profile Cylinder Components
Ram Plunger
Cylinder
Housing
Female Coupler
3/8” NPTF
Dust Cover
SAFETY and GENERAL INFORMATION
Save these instructions. For your safety, read and
understand the information contained within. The owner and
operator shall have an understanding of this product and safe
operating procedures before attempting to use this product.
Instructions and safety information shall be conveyed in
the operator’s native language before use of this product
is authorized. Make certain that the operator thoroughly
understands the inherent dangers associated with the use
and misuse of the product. If any doubt exists as to the safe
and proper use of this product as outlined in this factory
authorized manual, remove from service immediately.
Inspect before each use. Do not use if leaking, broken,
bent, cracked or otherwise damaged parts are noted. If the
cylinder has been or suspected to have been subjected to
a shock load (a load dropped suddenly, unexpectedly upon
it), discontinue use until checked out by a BVA Hydraulics
authorized service center. Owners and operators of this
equipment shall be aware that the use and subsequent
repair of this equipment may require special training and
knowledge. It is recommended that an annual inspection
be done by qualified personnel and that any missing or
damaged parts, decals, warning/safety labels or signs be
replaced with BVA Hydraulics authorized replacement parts
only. Any cylinder that appears to be damaged in any way, is
worn or operates abnormally shall be removed from service
immediately until such time as repairs can be made.
!
!
PRODUCT DESCRIPTION
BVA Hydraulics Single Acting Cylinder is designed for rated
capacity pushing, spreading and pressing jobs. A wide variety
of applications exist for this category of product. Special skill,
knowledge and training may be required for a specific task
and the product may not be suitable for all the jobs described
above. Unsuitable applications would include applications
that call for a device to move, level or support persons,
animals, hazardous materials, mobile homes/dwellings in
general, mirrors and/or plate glass, and/or to connect/secure
hatches, components, etc. between bulkheads. The user
ultimately must make the decision regarding suitability of the
product for any given task and therefore accept responsibility
for that decision. I mmediately after lifting, loads must be
supported by appropriate mechanical means.
NEVER use hydraulic cylinder as a support device!
Always check connections before using. Alteration
of these products is strictly prohibited. Use only those
adapters and attachments provided and approved by the
manufacturer.
WARNING: To reduce the risk of personal injury and/or
property damage, ensure that the rated working pressure of
each pressurized attachment be equal to or greater than the
rated working pressure developed by the hydraulic pump.
Model
Number
Cylinder
Capacity
(ton)
Stroke
(in)
Cylinder
Effective
Area
(in 2 )
Oil
Capacity
(in 3 )
Collapsed
Height
(in)
Extended
Height
(in)
Weight
(lb.)
Internal
Pressure
at
Capacity
(psi)
Cylinder
Housing
Dia.
(in)
Ram
Plunger
Dia.
(in)
Ram
Plunger
Mounting
Hole
HL1001 10 1.50 2.35 3.53 3.48 4.98 5.7 8,511 2.75 1.50 M4
HL2002 20 1.75 4.37 7.65 3.90 5.65 11 9,153 3.63 2.00 M4
HL3002 30 2.44 6.49 15.84 4.61 7.05 15 9,245 4.00 2.50 M5
HL5002 50 2.36 9.87 23.29 4.80 7.17 21.8 10,132 4.88 2.76 M5
HL10002 100 2.24 19.64 44.07 5.55 7.80 45.4 10,183 6.50 3.54 M8
SPECIFICATIONS
!