B&K Precision 9180 Series - Datasheet - Manual (Page 5)

www.bkprecision.com
Programmable Dual-Range DC Power Supplies
9170 & 9180 series
5
Specifications 9171 9172 9173 9174 9181 9182 9183 9184 9185
Output Rating
Low Range
0-10 V,
0-10 A 0-35 V,
0-3 A
0-10 V,
0-10 A 0-35 V,
0-3 A
0-18 V,
0-8 A
0-10 V,
0-20 A 0-35 V,
0-6 A
0-100 V,
0-2 A
0-400 V,
0-0.5 A
High Range
0-20 V,
0-5 A
0-70 V,
0-1.5 A
0-20 V,
0-5 A
0-70 V,
0-1.5 A
0-36 V,
0-4 A
0-20 V,
0-10 A 0-70 V,
0-3 A
0-200 V,
0-1 A
0-600 V,
0-0.35 A
Number of Channels 1 1 2 2 1 1 1 1 1
Max Output Power 100 W 105 W 200 W 210 W 144 W 200 W 210 W 200 W 210 W
Line Regulation
Voltage ≤ 0.01 %+1 mV
Current ≤ 0.01 %+250 uA
Load Regulation 1
Voltage ≤ 0.01 %+1 mV
Current ≤ 0.01 %+250 uA
Ripple and Noise
(20 Hz – 20 MHz)
Normal Mode
Voltage
≤ 0.35 mVrms
/ ≤ 3 mVpp
≤ 0.5 mVrms /
≤ 5 mVpp
≤ 0.35 mVrms
/ ≤ 3 mVpp
≤ 0.5 mVrms /
≤ 5 mVpp
≤ 0.35 mVrms /
≤ 3 mVpp
≤ 0.5 mVrms
/≤5 mVpp
≤ 1.5 mVrms /
≤ 15 mVpp
≤ 4.5 mVrms /
≤ 45 mVpp
Normal Mode
Current
≤ 2 mA rms
Common Mode
Current
≤ 1.5 uA rms
Programming /
Readback Resolution
Voltage 1 mV 2 mV 1 mV 2 mV 1 mV 2 mV 10 mV 20 mV
Current 1 mA 0.1 mA 1 mA 0.1 mA 1 mA 0.2 mA 0.1 mA 0.01 mA
Programming /
Readback Accuracy
±(% output+offset)
Voltage
≤ 0.05 %
+5 mV
≤ 0.05 %
+10 mV
≤ 0.05 %
+5 mV
≤ 0.05 %
+10 mV
≤ 0.05 %
+5 mV
≤ 0.05 %
+10 mV
≤ 0.05 %
+50 mV
≤ 0.05 %
+100 mV
Current
≤ 0.1 %
+2 mA
≤ 0.1 %
+1 mA
≤ 0.1 %
+2 mA
≤ 0.1 %
+1 mA
≤ 0.1 %
+2 mA
≤ 0.1 %
+5 mA
≤ 0.1 %
+2 mA
≤ 0.1 %
+1 mA
≤ 0.1 %
+0.1 mA
Temperature
Coefficient per °C
±(% output+offset)
Voltage ≤ 0.005 %+1 mV
≤ 0.005 %
+10 mV
≤ 0.005 %
+20 mV
Current ≤ 0.01 %+3 mA
Transient Response Time 2 ≤ 50 µs for output to recover to within 15 mV
≤ 100 µs for
output to
recover to within
50 mV
≤ 100 µs for
output to
recover to within
120 mV
Settling Time 3 ≤ 30 ms
Measurement Time ≤ 50 ms
OVP Accuracy ≤ 0.5 %+0.1 V ≤ 0.5 %+1 V
OCP Accuracy ≤ 0.5 %+0.1 A
OVP/OCP Response Time 4 ≤ 1 ms
Rising Time at Full Load / No Load ≤ 8 ms ≤ 10 ms ≤ 8 ms ≤ 10 ms ≤ 8 ms ≤ 10 ms ≤ 30 ms ≤ 40 ms
Falling Time at Full Load ≤ 8 ms ≤ 10 ms ≤ 8 ms ≤ 10 ms ≤ 8 ms ≤ 10 ms ≤ 30 ms ≤ 40 ms
Falling Time at No Load ≤ 250 ms
Stability (8 hrs)
±(% output+offset)
Voltage ≤ 0.02 %+2 mV
≤ 0.02 %
+10 mV
≤ 0.02 %
+20 mV
Current 0.1 %+1 mA
Notes:
1 With sense terminal connected.
2 Following a change in output current from full load to half load or vice versa.
3 Maximum time required for the output voltage to change from 1% to 99% or vice versa after receiving a VOLTage or VSET command via GPIB or USB interface.
4 Average time for output to start to drop after OVP/OCP condition occurs.