Extron Electronics MTP 4T 15HD RS Setup Guide User Manual
Setup guide — mtp 4t 15hd rs
Setup Guide — MTP 4T 15HD RS
Extron
USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron
USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron
Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron
Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron
Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron
China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron
Middle East
+971.4.2991800
+971.4.2991880 FAX
68-1398-50
Rev. A 02 09
INPUT
Tx Rx
RS-232
MONITOR
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected
RS-232
Device Pins
MTP
Pins
This sheet provides quick start instructions for an experienced
installer to set up and operate the MTP 4T 15HD RS
multiple VGA video and RS-232 transmitters.
N
Each MTP 4T 15HD RS transmitter
requires and at least one connected
compatible MTP receiver. Additional
receivers can be daisy chained.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the unit as required.
Step 2 — Transmitter inputs
•
Connect a computer (VGA) video source to each Input
connector.
•
Connect a VGA monitor to each Monitor connector.
•
Plug an RS-232 device into each RS-232 port. Wire the
connectors as shown below.
Step 3 — TP cables
Terminate up to four TP cables as shown at right.
Connect them between each transmitter’s Output
port and a receiver’s Input port.
Step 6 — Power
Plug a standard IEC power cord between the unit’s
power connector and 100 VAC to 240 VAC, 50 or
60 Hz power source.
N
Refer to the
MTP 15HD RS User’s Guide and the MTP 15HD RS Setup Guide to
setup and operate the receivers.
INPU
T
Tx
Rx
RS-232
MONITOR
OUTPU
T
PRE-PEAK
ON
OFF
INPU
T
Tx
Rx
RS-232
MONITO
R
OUTPU
T
PRE-PEAK
ON
OFF
INPU
T
Tx
Rx
RS-232
MONITOR
OUTPU
T
PRE-PEAK
ON
OFF
INPU
T
Tx
Rx
RS-232
MONITOR
OUTPUT
PRE-PEAK
ON
OFF
MT
P T
15
HD
R
S 1
MT
P T
15
HD
R
S 2
MT
P T
15
HD
R
S 3
MT
P T
15
HD
R
S 4
INPUT
BUFFERED
OUTPUT
OUTPUT
PO
WE
R
12V
.5A MA
X
MT
P R
L 1
5H
D
RS
ON
1
2
3
4
5
6
H SYNC
+
V SYNC
+
C SYNC
SO
G
VIDE
O
END UNI
T
RS-23
2
Tx
Rx
Extron
MTP 4T 15HD RS
4 Mini Twisted Pair
Transmitters
RS-232
RS-232
PC
Touchscreen
w/ RS-232
Control
Extron
MTP RL 15HD RS
Mini Twisted Pair
Receiver
TP Cable
Up to 500'
12345678
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A
T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
NOTE
If you are using Enhanced
Skew-Free™ A/V cable, use the
TIA/EIA T568A standard only.
Setup Guide — MTP 4T 15HD RS
Extron
USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron
USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron
Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron
Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron
Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron
China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron
Middle East
+971.4.2991800
+971.4.2991880 FAX
68-1398-50
Rev. A 02 09
INPUT
Tx Rx
RS-232
MONITOR
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected
RS-232
Device Pins
MTP
Pins
This sheet provides quick start instructions for an experienced
installer to set up and operate the MTP 4T 15HD RS
multiple VGA video and RS-232 transmitters.
N
Each MTP 4T 15HD RS transmitter
requires and at least one connected
compatible MTP receiver. Additional
receivers can be daisy chained.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the unit as required.
Step 2 — Transmitter inputs
•
Connect a computer (VGA) video source to each Input
connector.
•
Connect a VGA monitor to each Monitor connector.
•
Plug an RS-232 device into each RS-232 port. Wire the
connectors as shown below.
Step 3 — TP cables
Terminate up to four TP cables as shown at right.
Connect them between each transmitter’s Output
port and a receiver’s Input port.
Step 6 — Power
Plug a standard IEC power cord between the unit’s
power connector and 100 VAC to 240 VAC, 50 or
60 Hz power source.
N
Refer to the
MTP 15HD RS User’s Guide and the MTP 15HD RS Setup Guide to
setup and operate the receivers.
INPU
T
Tx
Rx
RS-232
MONITOR
OUTPU
T
PRE-PEAK
ON
OFF
INPU
T
Tx
Rx
RS-232
MONITO
R
OUTPU
T
PRE-PEAK
ON
OFF
INPU
T
Tx
Rx
RS-232
MONITO
R
OUTPU
T
PRE-PEAK
ON
OFF
INPU
T
Tx
Rx
RS-232
MONITOR
OUTPUT
PRE-PEAK
ON
OFF
MT
P T
15
HD
R
S 1
MT
P T
15
HD
R
S 2
MT
P T
15
HD
R
S 3
MT
P T
15
HD
R
S 4
INPUT
BUFFERED
OUTPUT
OUTPUT
PO
WE
R
12V
.5A MA
X
MT
P R
L 1
5H
D
RS
ON
1
2
3
4
5
6
H SYNC
+
V SYNC
+
C SYNC
SO
G
VIDE
O
END UNI
T
RS-232
Tx
Rx
Extron
MTP 4T 15HD RS
4 Mini Twisted Pair
Transmitters
RS-232
RS-232
PC
Touchscreen
w/ RS-232
Control
Extron
MTP RL 15HD RS
Mini Twisted Pair
Receiver
TP Cable
Up to 500'
12345678
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A
T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
NOTE
If you are using Enhanced
Skew-Free™ A/V cable, use the
TIA/EIA T568A standard only.