Extron Electronics MPA 401 Series Setup Guide - Manual

1
MPA 401-70V and MPA 401-100V • Setup Guide
This guide provides basic instructions for an experienced installer to install and configure the
Extron MPA 401-70V and MPA 401-100V mini power amplifiers.
INPUTS
OU TPU T
50/ 60 Hz
100 -24 0V .3A 2 1
3
4 L R
L R
L R
L R
L R
AUDI O
VID
1
2
3
4 Y
/VID
B-Y
H/
HV
R
/R- Y
V
G
/Y
B
/B- Y
RS- 232
LA N
RE SE T
AC T LINK
DV I-I
YC
SD I
R-Y /C RG B/R -Y,Y ,B-Y /YC /VID
I
N
P
U
T
O
U
T
P
U
T
I
N
P
U
T
O
U
T
P
U
T
POWE R
12V 1.5A M AX
OUTPUT
70V INPUTS
L (MONO)
(MONO )
R REMOTE
VOL/MUTE
MP A 401-70V
R
L
CLASS 2 WIRING
DO NOT GROUND OR SHOR T
SPEAKER OUTPUTS! 10V 50m A US
LIST ED 17T T AU DIO /VID EO AP PAR ATU S ®
Extron
SI 3CT LP
Full-Range
Ceiling Speakers
Extron
MPA 401
Mini Power
Amplifier
Extron
DVS 304 DVI AD
Digital Video
Scaler
with Audio
Audio
Flat Panel
Display
(DVI)
DSS Receiver
(S-video)
Laptop
(RGB)
DVD
(Component)
VCR
(Video)
Extron VC 50
Volume Controller
Extron
MLC 104 IP Plus
Controller
POWE R
12V 1.5A MA X
CLASS 2 WIR ING
L
(SUM MED)
(SUMMED) R
V C G
MP A 401-100V
R
L
10V 50m A REMOT E
100V O UTPU T
INPUT S
VC 50
Ex tro n
VOLUME
DB S R EC EIV ER
CO NF IG
DISP LA Y
MLC 104 IP
VO LU ME
1
2
3
4
ON OF F
Step 1 — Turn all of the equipment off and disconnect all power sources.
Step 2 — Mount the amplifier in either a plenum space, on a rack, under a desk, or on a projector.
ATTENTION: Although the amplifier is plenum rated, the power supply provided with it is not. The power supply must not be
placed in the plenum space. Cables to and from the amplifier must be plenum rated.
NOTE: Use only the two round mounting holes for mounting the MPA 401. The other four (hexagonal) holes anchor stand-offs
for the internal circuit boards. Using them may damage the amplifier and does not provide secure mounting for the unit.
Step 3 — Attach the speakers to the MPA 401 using the 2-pole, 5 mm screw-lock
captive screw speaker receptacle on the rear panel. (The old and new silk screens for the
MPA 401-100V are shown to the right).
ATTENTION: Do not ground or short the speaker outputs as this will damage the
amplifier.
NOTE: The mono audio speaker receptacle may be labeled in one of two ways (see
the images to the right). The wiring and function are the same whichever way the
product is labeled.
Step 4 — Attach sources to the MPA 401 unit from the audio source or projector.
The three rear panel audio inputs can be used individually or together:
z One pair of RCA receptacles (unbalanced)
z One 3.5 mm stereo tip-ring-sleeve receptacle (unbalanced)
z One 3.5 mm, 5-pole captive screw receptacle (balanced or unbalanced)
Balanced Mono Input
Tip
Ring
Sleeve
LR
Balanced Stereo Input
Tip
Ring
Tip
Ring
Sleeves
LR
Unbalanced Stereo Input
Tip
Sleeve
Sleeve
Tip
LR
Unbalanced Mono Input
Tip
Sleeve
LR
CLASS 2 WIRING
100V OUTPUT
Tip (+)
Sleeve ( )
RCA Connector
Sleeve ( )
Ring (R)
Tip (L)
3.5 mm TRS Connector
OUTPUT
100V