beautypg.com

Extron Electronics IN1508 Setup Guide User Manual

In1508 – setup guide, Installation and cabling, Connections

background image

N

For full installation, configuration, and operation details, refer to the

IN1508 User’s Manual, available at

www.extron.com

.

This guide provides quick start instructions for an experienced installer to set up and

operate the Extron IN1508 Scaling Presentation Switcher.

Installation and cabling

50/60Hz

100-240V 50-60Hz

I

N
P
U
T

VID

VID

YC

YC

Y

B-Y

R-Y

RGB

DVI

RS-232

1

2

4

5

3

L

1

2

3

4

5

6

7

R

AUDIO INPUT

8

L

A

B

R

OUTPUT

L

R

OUTPUT

RGB

Y, B-Y, R-Y

7

8

RGB

LISTED

1T23
I.T.E.

C

U S

6

2

5

9

8

4

3

1

6

12

11

7

10

Connections

a

AC power connector

g

Output 15-pin HD connector

b

Inputs 1 and 2 composite video BNC connectors

h

Audio Inputs 1 through 5 RCA connectors

c

Inputs 3 and 4 S-video mini-DIN connectors

i

Audio Inputs 6 through 8 3.5 mm mini stereo jacks

d

Input 5 component video BNC connectors

j

Audio Output A RCA connectors

e

Inputs 6 and 7 RGB video 15-pin HD connectors

k

Audio Output B captive screw connector

f

Input 8 DVI video connector (DVI-D only)

l

RS-232 9-pin D connector

Step 1 — Mounting

Turn off or disconnect all equipment power sources. For tabletop use, affix the rubber feet. For

optional rack mounting, secure the supplied brackets (see image at right) and mount in a rack.

Step 2 — Video inputs and output

a

.

Inputs 1 and 2

— Connect composite video

sources to these female BNC connectors.

b

. Inputs 3 and 4 — Connect S-video sources

to these 4-pin mini DIN connectors.

c

.

Input 5

— Connect a component video

(YUVi, YUVp, HDTV) source to these

female BNC connectors.

d

. Inputs 6 and 7 — Connect RGB video sources to

these 15-pin HD connectors.

e

.

Input 8

— Connect a single link of DVI-D video

to this DVI-I connector.

f

.

Output

— Connect an RGB or component video

display to this 15-pin HD output female connector.

Step 3 — Audio inputs and outputs

a

.

Audio Inputs 1 through 5 RCA connectors —

Connect stereo or mono audio sources.

b

. Audio Inputs 6 through 8 3.5 mm mini jacks — Connect computer

audio sources.

c

.

Output A RCA audio connectors —

Connect a stereo or mono audio

device (receiver, amplifier, or the like).

— OR —

Output B audio captive screw connector

— Connect a stereo or mono

audio device (receiver, amplifier, or the like); wire the connector as shown

at right.

68-791-50

Rev. A 04 10

IN1508 – Setup Guide

100-240V 50

-60H

z

I

N
P
U
T

VID

VID

YC

Y

B-Y

C-Y

RG

B

DV

I

1

2

4

5

3

L

2

3

4

5

6

7

R

AUDIO INPU

T

L

A

B

R

OUTPUT

L

R

OUTPUT

RG

B

Y, B-

Y, C-

Y

8

7

RG

B

6

LIS

TE

D

1T

23

I.T

.E.

C

U S

I

N
P
U

T

VID

VID

1

2

YC

YC

4

3

YC

Y

B-Y

R-Y

5

RGB

7

RGB

6

DVI

8

L

1

2

3

4

5

6

7

8

R

AUDIO INPUT

L

A

B

R

OUTPUT

L

R

OUTPUT

RGB

Y, B-Y, R-Y

For unbalanced audio output, connect
the sleeve(s) to the ground contact.

DO NOT connect the sleeve(s) to the
negative (-) contacts).

Unbalanced Stereo Output

Balanced Stereo Output

CAUTION

Tip

NO GROUND HERE.

Sleeve(s)

Tip

NO GROUND HERE.

Tip

Ring

Tip

Ring

L

R

L

R