Camp Chef GCLOG User Manual

Page 3

the area of the appliance. Clothing
or other flammable materials should
not be hung from the appliance,
or placed on or near the appliance.
Any guard or other protective device
removed for servicing the appliance
must be replaced prior to operating
the appliance.

Installation and repair should be
done by a qualified service person
The appliance should be inspected
before use and at least annually
by a qualified service person. More
frequent cleaning may be required
as necessary. It is imperative that
control compartment, burners and
circulating air passageways of the
appliance be kept clean.

Use caution when assembling and
operating fire pit to avoid cuts and
scrapes from rough or sharp edges.

Do not move the fire pit while it
is in use. Allow the fire pit to cool
completely before moving or storing.

When in use, the fire pit must be
on a level, stable surface in an area
clear of combustible material. An
asphalt surface (blacktop) may not
be acceptable for this purpose. Do
not operate fire pit on flammable
material such as carpet or a wood
deck. store the fire pit in a dry,
protected location.

This fire pit is not intended for and
should never be used as a heater.

DO NOT leave fire pit unattended
while in use. Operate the fire pit
with close supervision.

DO NOT operate around children or
animals.

Do not bump or tip fire pit. If
Fire pit becomes extremely hot -
allow fire pit to cool completely
before handling. If you must handle
the fire pit while it is hot, always
wear protective oven mitts or heat
resistant gloves when handling the
fire pit or its components.

DO NOT obstruct flow of combustion
air and/or ventilation air for fire pit.

Do not wear loose clothing while
operating the fire pit. Tie back long
hair while operating the fire pit.
ALWAYs wear fully covering shoes
while operating the fire pit.

Allow fire pit and its components
to cool completely before
conducting any routine cleaning or
maintenance. Do not move the fire
pit when in use. Allow the fire pit to
cool before moving or storing.

Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been
under water.

An LP cylinder not connected for use
should not be stored in the vicinity
of fire pit or any other fire pit. Do
not store spare LP cylinders within 10
feet of fire pit.
LP cylinders must be stored outdoors,
out of reach of children. Do not
store a spare LP-gas cylinder under
or near this fire pit. Never fill the
cylinder beyond 80 percent full.
Failure to follow these instructions
exactly could result in a fire causing
death or serious injury.

While the fire pit is not in use, the
gas must be turned off at the supply
cylinder. The fire pit should be shut
off and all supply valves (on piping
or on fuel cylinders) should be
closed in the event that the odor of
unburned gas is detected. Do not
attempt to use the unit until any gas
leaks are fixed. Do not use the fire
pit if the burner fails to light or fails
to remain lit. Under such conditions,
gas should be shut off and fuel
cylinders should be disconnected.
Do not operate under high wind
conditions. All installations are
to conform to local codes. In the
absence of local codes, installation
should conform to the National Fuel
Gas Code, ANsIZ223.1/NFPA 54

Fire pit should be installed with the
hose regulator assembly extended
at full length of hose directly
away from the burner. When so
configured, placement results in
maximum tank to fire pit distance.
When fire pit is operated, the hose/
regulator and gas tank should be
on a line perpendicular to wind
direction. Placing tank closer than
48” to the fire pit can overheat the
tank and cause release of propane
through relief openings and can
result in tank fire or explosion.

CONNECTING ThE lP TANk
1. The knob on the LP tank must be
closed. see that the knob is turned
clockwise to a full stop.
2. Check that the control knob on
the fire pit is turned off.
3. Remove the protective cap from
the LP tank valve and coupling nut,
if present.
4. Hold the regulator
in one hand and insert
the nipple into the
valve outlet. Be sure
the nipple is centered
in the valve outlet.
The coupler connects
to the large outside threads on the
valve outlet
5. Hand tighten the coupler
clockwise until it comes to a full
stop. Firmly tighten by hand only.
6. Place the tank to the side or rear
of the fire pit. Make sure the hose
does not touch any part of the
burner drum housing.

(B) Nipple has to
be centered into
the LP tank valve

0809-GCLOG-Instructions.indd 5-6

8/19/09 10:11:54 AM