Wilwood W6A WCCB Carbon-Ceramic Big Brake Front Brake Kit - Manual (Page 3)

General Information and Disassembly Instructions
Parts List
• Installation of this kit should ONLY be performed by persons experienced in
the installation and proper operation of disc brake systems. Before assembling
this Wilwood front disc brake kit, double check the following to ensure a trouble
free installation.
• Make sure this is the correct kit to fit the exact make and model year of your
vehicle. This kit is designed for direct bolt-on installation to 2005 through
present model year Mustang.
• Verify that the factory axle hub center register diameter and lug pattern match
those in the new hat. NOTE: Axle hubs that have been modified with different
size studs or lug patterns may require modifications to the new hat that must
be performed by a qualified machinist.
• Verify your wheel clearance using Figure 2.
• Inspect the contents of this kit against the parts list to ensure that all
components and hardware are included.
Disassembly Instructions
•Disassemble the original equipment front brakes:
Raise the front wheels off the ground and support the front suspension
according to the vehicle manufacturer’s instructions.
Remove the front wheels, calipers, rotors, and dust shields. Save the
Original Equipment Manufacturer (OEM) caliper mounting bolts.
•Remove any nicks or burrs on the axle hub and upright that may interfere with
the installation of the new brake components.
•Clean and de-grease the axle hub and upright.
CENTER
LINE OF
WHEEL
.50 (12,7)
RADIUS 1.19 (30,2)
3.80 (96,5) .23 (5,8)
4.59
(116,6)
8.05
(204,5)
CALIPER
WILWOOD ROTOR
WHEEL MOUNT SURFACE
NOTE: A MINIMUM OF .080” CLEARANCE MUST BE MAINTAINED
BETWEEN THE WHEEL AND CALIPER IN ALL AREAS
1.25 (31,8) ROTOR THICKNESS
2.80 (71,1)
CENTER REGISTRATION
Figure 2. Wheel Clearance Diagram
1
2
3
4
5
6
7
8
9
10
11
12
2
4
4
12
4
2
2
4
4
4
12
1
250-12626
230-10646
240-0476
240-6320
240-5878
160-13196
120-11663/64-RSN
230-9182
240-11101
230-9080
240-3902
150-12486K Bracket, Caliper Mounting
Bolt, M12-1.75 x 40mm
Washer, .477 I.D. x .922 O.D. x .063 Thick
Shim, .033 Thick
Shim, .015 Thick
Hat/Rotor Assembly, Carbon Ceramic, 1.25” Thk x 14.00” Dia, 12 x 8.75” Bolt Circle
Caliper, W6A, Nickel
Nut, 7/16-20 Self-Locking, 12 Point
Washer, .453 I.D. x .750 O.D. x .063 Thick
Stud, 7/16-14 x 7/16-20 x 3.375 long (pre installed in bracket)
Shim, .016 Thick
Pad, Axle Set
ITEM NO. PART NO. DESCRIPTION QTY
NOTES:
Part Number 160-13196 Rotor Assembly, includes p/n’s 160-12442, 170-12624, 230-6738, 240-11240, 300-12258, 300-12433 & 300-12434
Part Number 230-10647 Bracket Bolt Kit, includes part numbers 230-10646, 240-0476, 240-5878 and 240-6320
Part Number 250-12758 Caliper Bracket Kit, includes P/N’s 230-9080, 230-9182, 240-3902, 240-11101 and 250-12626
Page 3