Wilwood Combination Parking Brake Caliper 1Pc Rotor Rear Brake Kit - Manual (Page 3)

Parts List
General Information and Disassembly Instructions
• Installation of this kit should ONLY be performed by persons experienced in
the installation and proper operation of disc brake systems. Before
assembling this Wilwood rear disc brake kit, double check the following to
ensure a trouble free installation.
• Inspect the contents of this kit against the parts list to ensure that all
components and hardware are included.
• Make sure this is the correct kit to fit the exact make and model year of your
vehicle. This kit is designed for direct bolt-on installation to Factory Five
Roadster/Challenge car solid axle hubs.
• Verify your wheel clearance using Figure 2.
• Verify that the factory axle hub center register diameter and lug pattern
match those in the new hat and rotor registration adapter. NOTE: Axle hubs
that have been modified with different size studs or lug patterns may require
modifications to the new hat that must be performed by a qualified machinist.
Disassembly
• Disassemble the original equipment rear brakes:
Raise the rear wheels off the ground and support the rear suspension
according to the vehicle manufacturer’s instructions.
Remove the rear wheels and disassembly the brake assembly down to
the bare axle, including pulling out the axle per manufacturer’s
specifications and removing the OEM caliper mounting bracket.
• Remove any nicks or burrs on the axle housing flange, as well as the axle flange, that may interfere with the installation of the new
brake components.
• Clean and de-grease the axle and axle housing flange.
CENTER
LINE OF
WHEEL
.34 (8,6)
3.00 (76,2)
5.19 (131,8)
.58 (14,7)
15°
4.56
(115,8)
7.87
(199,9)
CALIPER
WILWOOD ROTOR
WHEEL MOUNT
SURFACE
NOTE: A MINIMUM OF .080” CLEARANCE MUST BE MAINTAINED
BETWEEN THE WHEEL AND CALIPER IN ALL AREAS
.81 (20,6) ROTOR THICKNESS
2.80 (71,1)
CENTER REGISTRATION
.87 (22,1)
RADIUS
Figure 2. Wheel Clearance Diagram
1
2
3
4
5
6
7
8
9
9A
10
10A
11
12
13
14
15
16
17
2
8
8
8
2
4
4
16
2
2
2
2
4
4
4
16
1
2
1
250-12052/53
230-2090
240-10190
230-5989
250-12055
230-10296
240-1159
240-1848
160-12150
160-9812/13-BK
120-10112/13-BK
120-10112/13-RD
230-9183
240-10190
230-9078
240-1159
150-9184K
300-11337
220-12093 Bracket, Flange (pair, one each, right and left)
Bolt, 3/8-24 x 1.25 Long, SHCS
Washer, .391 I.D. x .625 O.D. x .063 Thick
Nut, 3/8-24 Center Lock, Hex
Bracket, Caliper Mounting
Bolt, 7/16-14 x 1.25 Long, Hex Head
Washer, .453 I.D. x .750 O.D. x .063 Thick
Shim, .030 Thick
Rotor, ULHP .81” X 12.19” Dia.
Rotor, SRP Drilled and Slotted (one each, right and left)
Caliper, CPB, 41 mm (one each, right and left)
Caliper, CPB, 41 mm, Red
Nut, 3/8-24 Self Lock, 12 Point
Washer, .391 I.D. x .625 O.D. x .063 Thick
Stud, 3/8-16 x 3/8-24 x 2.50 Long (pre-installed in bracket)
Shim, .035 Thick
Pad, BP-10, Axle Set
Adapter, Rotor Registration
Flex Line Hose Kit (not shown)
ITEM NO. PART NO. DESCRIPTION QTY
NOTES: Part Number 230-12057 Bracket to Bracket Mounting Bolt Kit, includes P/N’s 230-10296, 240-1848 and 240-11101
Part Number 230-11448 Bracket Mounting Bolt Kit, includes P/N’s 230-2090, 230-5989 and 240-10190
Part Number 250-12054 Caliper Mounting Bolt Kit, includes P/N’s 230-9078, 230-9183, 240-1159, 240-10190 and 250-12055
Item 9A is an optional item and is included with the “-D” drilled kits. Add “-D” to end of part number when ordering
Item 10A is an optional item and is included with the “-R” red kits. Add “-R” to end of part number when ordering
Page 3