Wilwood Forged Dynalite Big Brake Front Brake Kit (Hub) - Manual (Page 3)

1
2
3
4
5
6
7
8
9
10
10A
11
12
13
14
15
16
17
17A
17B
18
19
20
21
22
1
2
4
2
10
2
2
2
2
2
2
16
10
2
2
2
2
2
2
2
4
4
16
1
2
249-10404/05
230-10424
240-11101
230-10296
230-2187
270-10442
370-0884
380-0885
300-3099
160-5843
160-7103/04
230-11934
230-11239
370-0882
240-2444
270-2158
211-1674
120-6816
120-6796-P
120-6816-RD
230-10025
240-10190
240-1159
150-8850K
180-0055S Brackets, Caliper Mounting (pair, one each, left and right)
Bolt, 7/16-14 x 2.00 Long, Hex Head
Washer, .453 I.D. x .750 O.D. x .063 Thick
Bolt, 7/16-14 x 1.25 Long, Hex Head
Stud, 1/2-20 x 1.75 Long, 12 Point
Hub Assembly
Bearing, Cone, Inner Bearing
Seal, Grease
Adapter, Rotor
Rotor, .81” Thick x 12.19” Dia, 8 x 7.00” Bolt Circle
Rotor, Drilled and Slotted
Bolt, 5/16-18 x 0.75 Long, Torx Button Head
Bolt, 3/8-16 x 1.0 Long, Torx Button Head
Bearing, Cone, Outer Bearing
Washer, Spindle, 7/8”
Cap, Dust
O-ring
Caliper, Forged Dynalite
Caliper, Forged Dynalite, Polished
Caliper, forged Dynalite, Red
Bolt, 3/8-24 x 1.25 Long, Hex Head
Washer, .391 I.D. x .625 O.D. x .063 Thick
Shim, .032 Thick
Pad, BP-10, Axle Set
Pin, Cotter
ITEM NO. PART NO. DESCRIPTION QTY
NOTES: Part Number 230-3829 Bolt Kit, adapter plate to hub, includes part number 230-11239
Part Number 230-12120 Bolt Kit, rotor to adapter plate, includes part number 230-11934
Part Number 230-11861 Bolt Kit, caliper to bracket, includes part numbers 230-10025, 240-10190 and 240-1159
Part Number 230-10441 Bolt Kit, bracket to spindle, includes part numbers 230-10296, 230-10424 and 240-11101
Item 10A is an optional item and is included in the “-D” Kits, Add “-D” to end of part number when ordering
Item 17A is an optional item and is included in the “-P” Kits, Add “-P” to end of part number when ordering
Item 17B is an optional item and is included in the “-R” Kits, Add “-R” to end of part number when ordering
Parts List
General Information
Installation of this kit should ONLY be performed by persons experienced in
the installation and proper operation of disc brake systems. Before assembling
the Wilwood front disc brake kit, double check the following items to ensure a
trouble free installation.
•Make sure this is the correct kit to match the exact make and model year of
the vehicles spindle (i.e., hubs for a 1975 Mustang spindle may not fit a 1982
Mustang spindle).
•Verify the hub stud pattern in this kit (5 x 4.50 or 5 x 4.75) matches the stud
pattern of the vehicles wheels.
•Inspect the package contents against the parts list to ensure that all
components and hardware are included.
•Verify your wheel clearance using Figure 2.
•WARNING: The wheel contact surfaces must seat completely on the face of
the hub. If any contact surfaces overhang the outside diameter of the hub
face, a 6.60” diameter x .20” thick steel spacer (Wilwood P/N 300-11961, sold
separately) MUST be used between the wheel and the hub.
•To prevent damage to the hub face, a 6.15” diameter x .09” thick hub shield
(Wilwood P/N 300-10716, sold separately) should be used with any stamped
steel wheels that do NOT overhang the outside diameter of the hub face.
CENTER
LINE OF
WHEEL
FACE OF ROTOR
ADAPTER
FACE OF HUB
WHEEL STUD
WHEEL MOUNTING
SURFACE
.81 (20,6)
ROTOR
THICKNESS
1.57 (40,0)
.25 (6,2)
.50 (12,7)
INSIDE
WHEEL
PROFILE
(MINIMUM
REQUIRED
FOR
CLEARANCE)
4.01
(101,9)
7.15
(181,6)
CALIPER
Figure 2. Wheel Clearance Diagram
Page 3