Wilwood Forged Dynalite 1 Piece Rotor and Hub Front Brake Kits - Manual (Page 3)

General Information and Disassembly Instructions
Parts List
Installation of this kit should ONLY be performed by persons experienced in the
installation and proper operation of disc brake systems. Before assembling the
Wilwood front disc brake kit, double check the following items to ensure a trouble-
free installation.
•Make sure this is the correct kit to match the exact make and model year of the
vehicles spindle (i.e., hubs for a 1945 Buick spindle will not fit a 1971 Buick spindle).
•Verify wheel clearance utilizing Figure 2.
•Inspect the package contents against the parts list to ensure that all components
and hardware are included.
•Verify the new hub stud pattern in this kit matches the lug pattern of the vehicles wheels.
Disassembly Instructions
•Disassemble the original equipment front brakes:
Raise the front wheels off the ground and support the front suspension
according to vehicle manufacturer’s instructions.
Remove the front wheels and completely disassemble the stock brake system
down to the bare spindles. Save the Original Equipment Manufacturer (OEM)
spindle nuts and nut locks (if any). NOTE: The driver’s side is left hand threads,
and the passenger’s side is right hand.
•Remove any nicks or burrs on the spindle mount faces that may interfere with the
installation of the new brake components.
•Clean and de-grease the spindles and saved components.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
2
4
2
2
2
2
2
2
2
2
2
2
4
4
16
1
2
2
249-12262/63
230-10425
230-10426
240-11101
370-2609
380-10792
160-12320
300-12295
370-9542
300-12413
240-12207
211-12404
270-12403
120-6814
240-10190
230-10025
240-1159
150-8850K
180-0056S
300-11961 Bracket, Caliper Mounting (pair, one each, left and right)
Bolt, 7/16-20 x 1.50 Long, Hex Head
Bolt, 7/16-20 x 2.50 Long, Hex Head
Washer, .453 I.D. x .750 O.D. x .063 Thick
Cone, Inner Bearing
Seal, Grease
Rotor, 1.29” Thk x 11.88” Dia, 5 x 5.00” Bolt Circle
Spacer, Spindle, 1.38 I.D. x 2.00 O.D. x .35 Thick
Cone, Outer Bearing
Spacer, Bearing, .86 I.D. x 1.50 O.D.
Washer, Spindle
O-ring
Dust Cap
Caliper, Forged Dynalite
Washer, .391 I.D. x .625 O.D. x .063 Thick
Bolt, 3/8-24 x 1.25 Long, Hex Head
Shim, 0.035 inch Thick
Pad, BP-10, Axle Set
Pin, Cotter
Spacer, Wheel, .20 Thick
ITEM NO. PART NO. DESCRIPTION QTY
NOTES:
Part Number 230-12316 Bolt Kit, bracket to spindle, includes part numbers 230-10425, 230-10426 and 240-11101
Part Number 230-11861 Bolt Kit, caliper to bracket, includes part numbers 230-10025, 240-10190 and 240-1159
.22 (5,6)
CENTER
LINE OF
WHEEL
1.25 (31,8) RADIUS
3.87
(98,3)
3.06
(77,7)
3.18 (80,8)
.09 (2,3) RADIUS
WHEEL MOUNT
SURFACE
6.89
(175,0)
CALIPER
WILWOOD ROTOR
NOTE: A MINIMUM OF .080” CLEARANCE MUST BE MAINTAINED
BETWEEN THE WHEEL AND CALIPER IN ALL AREAS
1.29 (32,8) ROTOR THICKNESS
Page 3
Figure 2. Wheel Clearance Diagram