Velleman DVM3218 - Manual (Page 7)

19.01.201
General
• Scre
• Switc
• Selec
“Hold”
Press
displ
“Range
Press
switc
rang
the “
the a
“Select”
Press
Automat
This
move
7.1 Vo
• Set t
meas
• Conn
• The
• Whe
• Press
the d
featu
LI b
while
impe
Notes:
• F
i
• W
“
7.2 Cu
• Set t
• Selec
curre
• Conn
• Read
11
l
w the desired t
ch the meter o
ct the desired
Function:
s the “DH” but
ay. Press agai
” function:
s the “RH” but
ching on the m
e for the selec
“RH” button; t
available range
” button:
s the “S” butto
tic battery savi
function switc
e the function
oltage meas
Do not meas
reside.
Always be car
fingers behind
terminals whe
the function sw
surements AC
nect the COM p
measured valu
n desired, sele
s the LI button
detection of ind
ure in circuits w
utton longer th
e normal voltag
edance of the m
For DC-measur
ndicated value
When the meas
“OL”. Select a h
urrent meas
Do not measu
Current measu
Always be car
fingers behind
the function sw
ct the AC or DC
ent).
nect the COM p
d the measured
test pin [1] fir
on by moving t
range within th
tton [2] to free
n to resume no
tton [3] to swi
meter it will be
cted function. W
he icon is s
es. To return to
on [4] to selec
ing mode:
hes the meter
switch to react
surements
sure circuits w
reful when wor
d the probe bar
en the meter is
witch to V a
or DC measur
probe [9] and
ue appears on t
ect a range ma
n [6] to lower
duced (ghost)
where voltages
han 3s. In case
ges will still rea
meter is shunte
rements: when
e is preceded by
sured value is
higher range.
surements
ure current in c
urements: max
reful when wor
d the probe bar
witch to A /A
C range with th
probe [9] and
d value from th
DVM3
7
rmly on the me
he function sw
he function by
eze the value o
ormal operatio
tch between a
in auto-ranging
When desired t
shown on the d
o auto-ranging
ct the desired r
to battery sav
tivate the mete
where voltage
king with volta
rriers at all tim
s linked to a cir
and press the S
rements.
test pin [1] to
the display.
nually with the
the imput imp
voltages from
s higher than 2
e of ghost-volta
ad a considera
ed with the imp
n a negative po
y a “-” sign.
higher than th
circuits with vo
x. 400mA.
king with volta
rriers at all tim
A
.
he S button [4
test pin [1] in
he display.
3218
eter.
witch [8] to the
pressing the r
onto the displa
n.
utomatic and m
g mode. The m
the range can b
display. Press m
press and hol
range within th
ving mode after
er.
es > 600V CA
ages above 60V
mes during mea
rcuit which is b
S button [4] to
o the circuit un
e RH button [3
pedance from 1
nearby energiz
250V (CAT II) m
ages the meter
ble value (how
pedance of the
olarity is presen
e selected rang
ltages > 250V
ages above 60V
mes during mea
4] (AC = altern
n series with th
e desired funct
ange select bu
ay. The sym
manual range s
meter chooses t
be selected ma
multiple times
d the “RH” but
e selected func
r ±8 min. Push
AT III or > 10
Vdc or 30Vac r
asurement. Do
being tested.
o choose betwe
der test.
3].
10MΩ to ±400K
zed circuits. DO
may occur and
r reading will b
wever incorrect
e circuit under
nt at the red te
ge limit, the di
Vdc or 30Vac r
asurement.
nating current,
e circuit.
©Vellema
ion.
utton [4].
bol appears on
selection. Whe
the most suita
anually by pres
to scroll throug
tton for 2 seco
ction.
h any button or
000V CAT II m
rms. Keep your
not touch unu
een AC
KΩ. This enable
O NOT use thi
do not press t
be close to 0 V,
t as the low
test).
est pin [1], the
splay will show
rms. Keep your
DC = direct
an nv
n the
en
ble
ssing
gh
nds.
r
may
r
used
es
s
the
,
e
w
r