Milton CAT 14M - Manual (Page 20)

20 14M Motor Grader specifications
Tandems
Height 616 mm 24.25 in
Width 214 mm 8.4 in
Sidewall thickness – inner 20 mm 0.8 in
Sidewall thickness – outer 20 mm 0.8 in
Drive chain pitch 57 mm 2.24 in
Wheel axle spacing 1656 mm 65 in
Tandem oscillation – front up 15°
Tandem oscillation – front down 25°
Moldboard
Moldboard – width 4.3 m 14 ft 0 in
Moldboard – height 688 mm 27 in
Moldboard – thickness 25 mm 1 in
Arc radius 413 mm 16.3 in
Throat clearance 117 mm 4.6 in
Cutting edge – width 203 mm 8 in
Cutting edge – thickness 16 mm 0.6 in
End Bit – width 152 mm 6 in
End Bit – thickness 16 mm 0.6 in
Blade Pull – base GVW 14 093 kg 31,069 lb
Blade Pull – max GVW 17 997 kg 39,678 lb
Down Pressure – base GVW 10 094 kg 22,254 lb
Down Pressure – max GVW 17 539 kg 38,666 lb
• Blade pull calculated at 0.9 traction coefficient, which is
equal to ideal no-slip conditions, and Gross Machine Weight.
Blade Range
Circle centershift – right 520 mm 20.5 in
Circle centershift – left 650 mm 25.5 in
Moldboard sideshift – right 790 mm 31.1 in
Moldboard sideshift – left 740 mm 29.1 in
Maximum blade position angle 65°
Blade tip range – forward 40°
Blade tip range – backward 5°
Maximum shoulder reach outside of tires
– right 2279 mm 89.7 in
– left 2169 mm 85.4 in
Maximum lift above ground 419 mm 16.5 in
Maximum depth of cut 438 mm 17.3 in
Operating Specifications
Top Speed – Fwd. 49.8 km/h 31 mph
Top Speed – Rev. 39.4 km/h 24.5 mph
Turning radius, outside front tires 7.9 m 25 ft 11 in
Steering range – left/right 47.5°
Articulation angle – left/right 20°
Fwd. 1st 4.3 km/h 2.7 mph
Fwd. 2nd 5.9 km/h 3.7 mph
Fwd. 3rd 8.6 km/h 5.3 mph
Fwd. 4th 11.8 km/h 7.3 mph
Fwd. 5th 18.3 km/h 11.4 mph
Fwd. 6th 24.8 km/h 15.4 mph
Fwd. 7th 34.2 km/h 21.3 mph
Fwd. 8th 49.8 km/h 31 mph
Rev. 1st 3.4 km/h 2.1 mph
Rev. 2nd 6.4 km/h 4 mph
Rev. 3rd 9.3 km/h 5.8 mph
Rev. 4th 14.5 km/h 9 mph
Rev. 5th 27.1 km/h 16.9 mph
Rev. 6th 39.4 km/h 24.5 mph
Service Refill
Fuel Capacity 492 L 130 gal
Cooling system 46.5 L 12.3 gal
Hydraulic system – tank 60 L 15.9 gal
Engine Oil 30 L 7.9 gal
Trans./Diff./Final Drives 89 L 23.5 gal
Tandem housing (each) 96.5 L 25.5 gal
Front wheel spindle 0.9 L 0.24 gal
bearing housing
Circle drive housing 6 L 1.6 gal
Frame
Circle – diameter 1822 mm 71.75 in
Circle – blade beam thickness 50 mm 2 in
Drawbar – height 203.2 mm 8 in
Drawbar – width 76.2 mm 3 in
Front frame structure
– height 406.4 mm 16 in
– width 304.8 mm 12 in
– thickness 15.9 mm 0.6 in
Front axle
– height to center 640 mm 25.2 in
– wheel lean, left/right 17.1°
– total oscillation per side 32.0°