Milton CAT 140M - Manual (Page 22)

22 140M Motor Grader specifications
Tandems
Height 506 mm 19.9 in
Width 201 mm 7.9 in
Sidewall Thickness – Inner 16 mm 0.6 in
Sidewall Thickness – Outer 18 mm 0.7 in
Drive Chain Pitch 50.8 mm 2 in
Wheel Axle Spacing 1523 mm 60 in
Tandem Oscillation – Front Up 15°
Tandem Oscillation – Front Down 25°
Moldboard
Moldboard – Width 3.7 m 12 ft
Moldboard – Height 610 mm 24 in
Moldboard – Thickness 22 mm 0.87 in
Arc Radius 413 mm 16.3 in
Throat Clearance 166 mm 6.5 in
Cutting Edge – Width 152 mm 6 in
Cutting Edge – Thickness 16 mm 0.6 in
End Bit – Width 152 mm 6 in
End Bit – Thickness 16 mm 0.6 in
Blade Pull – Base GVW 9873 kg 21,766 lb
Blade Pull – Max GVW 13 458 kg 29,670 lb
Blade Pull – Base GVW (AWD) 14 229 kg 31,370 lb
Blade Pull – Max GVW (AWD) 17 815 kg 39,276 lb
Down Pressure – Base GVW 7137 kg 15,734 lb
Down Pressure – Max GVW 13 932 kg 30,716 lb
• Blade pull calculated at 0.9 traction coefficient, which is
equal to ideal no-slip conditions, and Gross Machine Weight.
Blade Range
Circle Centershift – Right 728 mm 28.7 in
Circle Centershift – Left 695 mm 27.4 in
Moldboard Sideshift – Right 660 mm 26 in
Moldboard Sideshift – Left 510 mm 20.1 in
Maximum Blade Position Angle 90°
Blade Tip Range – Forward 40°
Blade Tip Range – Backward 5°
Maximum Shoulder Reach Outside of Tires
– Right 1978 mm 77.9 in
– Left 1790 mm 70.5 in
Maximum Lift Above Ground 480 mm 18.9 in
Maximum Depth of Cut 715 mm 28.1 in
Operating Specifications
Top Speed – Fwd. 46.6 km/h 29 mph
Top Speed – Rev. 36.8 km/h 22.9 mph
Turning Radius, Outside Front Tires 7.57 m 24 ft 10 in
Steering Range – Left/Right 47.5°
Articulation Angle – Left/Right 20°
Fwd. 1st 4 km/h 2.5 mph
Fwd. 2nd 5.5 km/h 3.4 mph
Fwd. 3rd 8 km/h 5 mph
Fwd. 4th 11 km/h 6.8 mph
Fwd. 5th 17.1 km/h 10.6 mph
Fwd. 6th 23.3 km/h 14.5 mph
Fwd. 7th 32 km/h 19.9 mph
Fwd. 8th 46.6 km/h 29 mph
Rev. 1st 3.2 km/h 2 mph
Rev. 2nd 6 km/h 3.7 mph
Rev. 3rd 8.7 km/h 5.4 mph
Rev. 4th 13.5 km/h 8.4 mph
Rev. 5th 25.3 km/h 15.7 mph
Rev. 6th 36.8 km/h 22.9 mph
Service Refill
Fuel Capacity 398 L 105 gal
Cooling System 40 L 10.6 gal
Hydraulic System – Tank 64 L 16.9 gal
Engine Oil 25 L 6.6 gal
Trans./Diff./Final Drives 64 L 16.9 gal
Tandem Housing (each) 64 L 16.9 gal
Front Wheel Spindle 0.5 L 0.13 gal
Bearing Housing
Circle Drive Housing 7 L 1.8 gal
Frame
Circle – Diameter 1530 mm 60.2 in
Circle – Blade Beam Thickness 40 mm 1.6 in
Drawbar – Height 152 mm 6 in
Drawbar – Width 76.2 mm 3 in
Front Frame Structure
– Height 305 mm 12 in
– Width 305 mm 12 in
– Thickness 16 mm 0.6 in
Front Axle
– Height to Center 571 mm 23 in
– Wheel Lean, Left/Right 18°
– Total Oscillation Per Side 32°