Skil 0770 RT - Manual (Page 9)

9
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Maintain the tool with care and keep it clean
- always ensure that the ventilation openings are kept
clear of debris
! disconnect the plug before cleaning
• Regularly check for defects such as loose, dislodged or
damaged blade, loose fixings, and worn or damaged
components
• Have worn or damaged parts replaced for safety reasons
• Avoid bending safety lock N ) which may cause
disfunctioning of the tool
• Always switch off the tool, allow the cutting blade to stop,
disconnect the plug and allow the tool to cool down before
inspecting, adjusting, servicing, and/or storing the tool
• Store the tool indoors in a dry place
• When servicing the shredding unit be aware that, even
though the motor will not start due to the safety-lock
feature of the guard, the shredding unit can still be moved
by hand
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol @ will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that the product
described under “Technical data” is in conformity with the
following standards or standardization documents: EN
60335, EN 13683, EN 61000, EN 55014 in accordance
with the provisions of the directives 2006/95/EC,
2004/108/EC, 2006/42/EC, 2000/14/EC, 2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
¹КБВЖО¹Ж¼½К
ЗЗ¾¼½Ж
И½К¹МБЗЖЛŵЖ¿БЖ½½КБЖ¿
НКЗИ½Ɠˁ˅ʿ˂ ʽ¼¹Ɠ
Д¹¾ БВГ¿К¹¹¾
ИИКЗО¹Д¹Ж¹¿½К
30.07.2013
11
NOISE
• Measured in accordance with 2000/14/EC (EN/ISO
3744) the guaranteed sound power level LWA is lower
than 113 dB(A) (conformity assessment procedure
according to Annex V)
Notified body : KEMA, Arnhem, NL
Notified body identification number : 0344
Broyeur 0770
INTRODUCTION
• Cet outil n’est conçu pour un usage professionnel
• Cet outil a pour objectif de couper les déchets de bois et
de fibres pour le compostage
• Vérifiez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
• Lisez attentivement ce manuel d’instruction avant
d’utiliser l’outil et conservez-le pour pouvoir vous y référer
ultérieurement 3
• Prêtez attention aux consignes de sécurité et aux
avertissements; ne pas suivre ces instructions peut
entraîner des graves blessures
CARACTERISTIQUES TECHNIQUES 1
✱
) Le mode de service S6 (P40 = 40%) désigne un profil de
charge supposant une charge de 4 min et une marche à
vide de 6 min (pour une utilisation dans la pratique, un
service permanent est possible)
ELEMENTS DE L’OUTIL 2
A Clé (2)
B Bac récolteur
C Sortie
D Support de sonde
E Interrupteur marche/arrêt
F Bouton de protection
G Bouton de redémarrage
H Ouverture d’alimentation
J Fentes de ventilation
K Sonde
L Clé hexagonale
M Plaque métallique
N Blocage de sécurité
SECURITE
INSTRUCTIONS SPECIFIQUES DE SECURITE
RELATIVES AUX BROYEURS
EXPLICATION DES SYMBOLES SUR L’OUTIL
3
Veuillez lire le mode d’emploi avant d’utiliser l’outil
4
Arrêtez et débranchez la fiche avant tout nettoyage/
toute maintenance ou si le câble (la rallonge) est
endommagé(e) ou entremêlé(e)