Learning function – Hama ROC4505 User Manual

Page 8

Note: during the programming of a macro, the time bet-

ween each step is limited to a few seconds.This leaves little

time for reading the instructions and then carrying them

out. If the mode indicator light blinks and then goes out, it

is because this time limit has been exceeded,you must start

again from step 1.

To record a MACRO:

1. Press and hold down the

SETUP

key until the

mode key blinks (

VCR

, …) and then

remains lit (after 2 or 3 seconds).

2. Release the

SETUP

key.

3. Press the

MACRO

key once. The mode key

blinks.

4. Press once the A, B, or C key which you are

going to use to memorise the sequence.

5. Press once on the (

VCR

, …) mode key of

the first device you wish to control (the first

key must always be a mode key.)

6. Successively press the keys corresponding to

the commands you wish to send to the

device(s) (9 keys maximum, including other

mode keys).The mode key blinks when each

key is pressed.

7. Memorise your key sequences by pressing

the

MACRO

key once. The mode key is no

longer lit and your Macro is complete.

Note: a sequence will be automatically memorised after

the tenth key press (counted from the mode key) and the

mode key light will go out.

To use a MACRO:

Press the

MACRO

key once and, within 20

seconds, press the A, B, or C key you used to

memorise the sequence.

Note: when running a Macro (which takes a few

seconds), ensure that the remote control is aimed at the

device being controlled.
Remarks:

• The default time between sending 2 commands when

using a macro is half a second.. However, it is possible

that you will need to add longer periods in your

sequence in order to allow enough time for certain devi-

ces to turn themselves on.To lengthen the time period

between 2 commands, press once on the

key and

then press one of the keys from 1 to 9 in order to insert

a pause from 1 to 9 seconds.

• The first key in a sequence must always be a (

VCR

, …) mode key.

Deleting a MACRO:

1. Press and hold down the

SETUP

key until the

mode key blinks (

VCR

, …) and then

remains lit (after 2 or 3 seconds).

2. Release the

SETUP

key.

3. Press once on the

MACRO

. key. The mode

key begins to blink.

4. Press once the A, B, or C key that repre-

sents the sequence to delete.

5. Press and hold down the

SETUP

key. The

mode key light goes out and the sequence is

now deleted.

Learning function

If the make of the device you wish to control is

not in the separate code list,you can copy the key

functions of the original remote control of the

device into your ROC 4505. Depending on the

format of the transmission codes of the original

remote control,your ROC 4505 remote control can

memorise up to 150 keys

Global delete – Delete all the keys

copied (this is recommended the

first time you use this function)

1. Hold down the

SETUP

key until the key cor-

responding to the last selected mode remains

lit.

2. Release the

SETUP

key.

3. Press twice on the

LEARN

. key.The key goes

out and then relights.

4. Press once on the

SETUP

key. The mode key

goes out after several seconds.

5. All the copied keys are now deleted.

Before starting

• The batteries in the 2 remote controls must be in

good condition; change them if necessary.

• The keys L1 to L4 allow you to copy 4 additional

keys.

• First copy 2 or 3 keys from the original remote

control in order to check the compatibility of the

codes of both remote controls.Then carry out a glo-

bal delete of these keys before starting the full

learning procedure.

• Lay out the original remote control and your ROC

4505 end to end so as to align the LED diodes on

the 2 remote controls. Where necessary adjust the

height of both remote controls so that the LED dio-

des are properly aligned.

• Check that the 2 remote controls are approximately

2.5 cm apart (a thumb width).

• Do not move the remote controls during the learning

procedure.

• Ensure that the room is not lit by fluorescents tubes

or low consumption lamps since such light sources

can interfere with the copying.

• The 2 remote controls must be at least one metre

away from any light source.

• Avoid copying

VOL

and

keys codes and the play

keys (8) since depending on the remote controls the

codes of these keys do not necessarily control the

same devices.

• When the memory of your ROC 4505 is full, the

mode key will blink for 3 seconds. It is then not pos-

sible to copy any more codes without first carrying

out a global delete.

• When you copy a key, it is possible that the mode key

will blink feebly. In this case, do not release the key

and wait until the blinking stops.

Note 1: if the learning procedure does not seem to work

correctly, try the following:

1. End the learning procedure by pressing

SETUP

2. Check that the LEDs of the two remote controls

are properly aligned. Carry out the alignment

procedure.

3. Modify the distance between the remote

controls, increasing or reducing the distance from

1.5 cm to 5 cm.

4. Restart the procedure from the beginning.

ROC4505_en 3/11/06 16:18 Page 4