Dremel Клеевой пистолет DREMEL 920 - Manual (Page 6)

6
PICTURE 1a/1b
1. Nozzle
2. Glue
stick
3. Feed trigger
4. Stand
5. Temperature
switch
PICTURE 1c
6.
On/off switch with indicator light
7. Detachable cord
8. Stand release button
9. Exchangeable nozzle
USE
SWITCHING ON/OFF
SWITCHING ON:
Plug Dremel Glue Gun into a standard 230 V
electrical outlet.
Models 910, 920 and 930:
•
Once the glue gun is plugged in, it is on and
heating.
Dual Temperature Glue Gun Model 930:
•
Adjust switch (5) to low or high temperature
setting to turn the Glue Gun on. Consult with
glue stick package to determine appropriate
temperature.
Model 940:
•
Connect the power cord to the glue gun.
• Switch the glue gun on with the main switch.
Indicator light (6) will let you know the glue gun
is on and heating.
SWITCHING OFF:
•
Pull the mains plug (models 910, 920 and 930).
• Switch the unit ON/OFF with switch (6; model
940). Pull the mains plug.
Allow the unit to cool completely before storing. The
hot nozzle can cause damage.
GETTING STARTED
PREPARATIONS FOR GLUING
The surfaces to be glued must be clean, dry and
free of grease. Roughen smooth surfaces before
gluing. DO NOT USE INFLAMMABLE SOLVENTS FOR
CLEANING! The ambient temperature and the work
piece to be glued must not be colder than +5 °C or
warmer than +50 °C. Warm rapidly cooling materials
(e.g., steel) for better adhesion.
GLUING
DANGER OF BURNING! The glue and the nozzle tip (1)
become very hot. Do not allow the nozzle tip or hot
glue to come into contact with persons or animals. If
hot glue touches the skin, immediately hold the spot
for some minutes under a stream of cold water. Do not
try to remove the glue from the skin.
Models 910, 920 and 930:
•
Allow glue gun to reach operating temperature
before using (±5mins).
Insert the glue stick (2). Press the feed
trigger (3).
Model 940:
•
Once the cord is detached, the glue gun
remains operable for 5mins, before it needs to
heat up.
NOTE: For your first use, you may need to load up to
two full glue sticks before glue begins to flow.
•
Squeeze trigger (3) to apply glue onto desired
surface.
• Apply parts together.
• Allow glue to cool before handling object or
surface.
TIP: Dremel also supplies glitter and colour sticks
for decorative purposes. These sticks have been
specially developed for creative projects and low
temperature (105 °C).
The colour sticks can also be used for sealing
decorations. To be able to quickly change colours, it
is recommended to cut the sticks into 3 cm pieces
before inserting into the Glue Gun.
GLUESTICKS
Glue
Model 910 920 930 940
165°C
105°C
165°C
105°C 195°C
GG01 Multipurpose glue, 7mm - -
GG02 Multipurpose glue, 7mm - -
GG03 Woodglue, 7mm - -
GG04 Glitter glue, 7mm - -
GG05 Colour glue, 7mm - -
GG11 Multipurpose glue, 11mm - - -
GG13 Woodglue, 11mm - - -
2610399275-GlueGun-EU-0610.indb 6 10399275-GlueGun-EU-0610.indb 6 3-6-2010 12:47:04 3-6-2010 12:47:04