Yeoman EXE MIDI PR1145 - Manual (Page 11)

11
2.7 The stove is fitted with the Gazco Flue Sure System, which
will act to cut off the gas supply to the appliance in the
event of incorrect operation of the flue. If the system acts
to shut off the gas supply, this indicates that there is
insufficient flue pull. If this occurs, a minimum of 10
minutes should be allowed before trying to relight.
Continued operation of this safety device means that there
may be a serious problem with the flue system; a qualified
gas engineer should inspect this. DO NOT USE THE
STOVE UNTIL AN ENGINEER SAYS IT IS SAFE TO DO
SO.
2.8 The Flue Sure System must not be tampered with. Use only
genuine Gazco replacement parts when servicing the
system - refer to servicing section on page 14.
3. INSTALLATION OF THE STOVE
3.1 Open the carton, remove the accessory carton and stove
unit. It will now be necessary to decide upon top or rear
flue exit. The stove is factory built for rear flue exit but it
may be changed to top exit by simply interchanging the
flue spigot and blanking plate located on the stove.
3.2 Position the stove ensuring all appropriate clearances are
observed. Using a pencil, mark the position of the holes in
the fixing brackets attached to the inside of the rear legs.
3.3 Remove the stove and drill the holes using a number 12
masonry drill. Push wall plugs into the holes and insert the
wood screws until the head is approximately 3mm proud
of the hearth. Place the stove in position so that the screw
heads are located in the large part of the slot in the
bracket. Push the stove back so that the screw heads
engage fully into the narrow part of the slot, tighten the
screws as required.
3.4 Having run the gas supply to the stove, PURGE THE
SUPPLY PIPE . This is essential to expel any debris that may
block the gas controls. Connect the gas supply to the
8mm-compression elbow at the RH rear corner of the
stove. There is a cutout in the RH rear leg to enable a
direct straight connection to be made to the rear of the
stove (see Diagram 4). A gas soundness check must be
completed up to the gas inlet connection.
4
AR0934
IMPORTANT: ENSURE THAT THE APPLIANCE IS
CORRECTLY ADJUSTED FOR THE GAS TYPE AND
CATEGORY APPLICABLE IN THE COUNTRY OF USE.
REFER TO DATA BADGE AND TECHNICAL
SPECIFICATION AT THE FRONT OF THIS BOOkLET.
FOR DETAILS ON CHANGING BETWEEN GAS TYPES
REFER TO SECTION 11 PAGE 20 .
1. CONTROL UPGRADE
1.1 The stove is fitted with a control valve that can be upgraded
to support a battery powered remote control. Two types of
remote control can be obtained through your local Gazco
stockist:
1.2 This upgrade can be fitted before or after installation but if
side clearances are limited then it will be easier to upgrade
the stove before installation. Full instructions are included
with the kit.
1.3 The Standard Remote Control (Gazco Part No. 8455)
controls the gas stove after the pilot is lit so you can regulate
the main burner through its range of settings and turn the
burner off leaving just the pilot lit.
1.4 The Thermostatic and Timer Remote Control (Gazco Part
No. 8456) controls the stove after the pilot is lit using three
modes:
—
Manual Mode – used to turn the burner on and off and
regulate it through its range of settings.
—
Auto Mode – used to turn the burner on and off and
regulate the heat to a pre-set temperature.
—
Timer Mode – used to turn the burner on and off at two
pre-set times and regulate the heat to a pre-set
temperature during those periods.
2. SAFETY PRECAUTIONS
1.1 This stove must be installed in accordance with the rules in
force. Read these instructions before installing the stove.
1.2 All the instructions must be left, intact, with the user.
1.3 In the interests of your own and other’s safety, this stove
must be installed by a competent person according to local
and national codes of practice. Failure to install the stove
correctly could lead to prosecution.
1.4 This stove is for use on a governed gas installation and set to
the required pressure.
1.5 Keep all plastic bags away from young children.
1.6 Do not place any object on or near the stove. Leave
adequate clearance above the stove (see Site Requirements,
Diagram 2).
INSTALLATION INSTRUCTIONS
INSTALLATION