Yamaha RX-V795RDS - Manual (Page 11)

9
English
Controls and their functions
Front panel
NATURAL SOUND AV RECEIVER RX V795RDS
SPEAKERS PHONES
A
ON OFF ON OFF
B
BASS TREBLE BALANCE VIDEO AUX
S VIDEO VIDEO L AUDIO R
VOLUME
INPUT SELECTOR
5 5
4
3
2
l 0 l
2
3
4
5 5
4
3
2
l 0 l
2
3
4
L R
l6
20
28
40
60
l2
8
4
2
0
–dB
BASS
EXTENSION
TONE
BYPASS
5 5
4
3
2
l 0 l
2
3
4
LEVEL EFFECT
SET
MENU
PROGRAM
A/B/C/D/E 1 2 3 4 5 6 7 8 MEMORY EDIT FM/AM DOWN TUNING UP INPUT MODE
TUNING
MODE
MAN’L/AUTO FM AUTO/MAN’L MONO
PRESET
kHz
MHz
MEMORY
AM
FM
SLEEP AUTO
TAPE 2 MONITOR
DIGITAL
STEREO
0 20 l00 ROOM 2 CONTROL
NORMAL WIDEPHANTOM
40 60
SPEAKERS
RT PS PTY PTY HOLD EON NEWS INFO AFFAIRS SPORT
PCM AC—3
CT
DSP PRO LOGIC DIGITAL DIGITAL
AUTO TUNING
A
SPEAKERS
B
ROOM 2
70 mm
ENHANCED dB ms
TAPE/MD MON
/EXT. DECODER
STANDBY/ON
CINEMA DSP
1
8 A B 0 C D
I J K L
M N O R T
P
S Q
2 3 4 5 6
7 9
RDS MODE
/ FREQ EON
MODE START
PTY SEEK
MEMORY EDIT FM/AM
TUNING
MODE
MAN’L/AUTO FM AUTO/MAN’L MONO
RDS MODE
/ FREQ EON
MODE START
PTY SEEK
EFGH
1
STANDBY/ON switch
Press this switch to turn on the power. Press this switch again
to set this unit in the standby mode.
* A click from the switch and the initial rotation of the built-in
fan will be heard when the power is turned on.
Standby mode
This unit is still using a small amount of power in this mode
in order to be ready to receive infrared-signals from the
remote controller.
2
Remote control sensor
Receives signals from the remote controller.
3
Display panel
Displays a variety of information. (Refer to page 11 for details.)
4
TAPE/MD MON/EXT. DECODER button
Press this button repeatedly until the “TAPE/MD MONITOR”
indicator is illuminated on the display. Sound source played or
recorded on the unit connected to the TAPE/MD IN
(PLAY)/OUT (REC) AUDIO SIGNAL terminals on the rear of
this unit is selected as the input source taking priority of the
INPUT SELECTOR’s setting.
Press this button repeatedly until the “EXT. DECODER”
appears on the display. Sound signals input to the EXTERNAL
DECODER INPUT terminals on the rear of this unit is selected
as the input source taking priority of the INPUT SELECTOR’s
setting.
Press this button repeatedly until the original display mode is
restored to cancel the above input sources.
5
INPUT SELECTOR
Turn this knob to select the input source.
The selected source will be shown on the display.
6
Master VOLUME control
Simultaneously controls volume for all output sounds; main,
rear, center and subwoofer. (The REC OUT level is not
affected.)
* The indicator on the master VOLUME control will flash when
the volume is decreased by pressing the MUTE key on the
remote controller.
7
PHONES jack
Headphones can be plugged into this jack for private listening.
You can listen to the sound to be output from the main
speakers through headphones. When listening with
headphones privately, set both SPEAKERS A and B switches
to the OFF position and turn off the digital sound field
processor by pressing the EFFECT button so that no DSP
program name is illuminated on the display panel.
For the remote controller, refer to pages 65 to 72.
GETTING STARTED
PHONES