Yeoman YM-W9122FL - Manual (Page 9)

9
1. GENERAL CLEANING
Before any cleaning is carried out, allow the stove to
cool thoroughly to avoid risk of burns.
1.1 We would recommend that your Yeoman stove be cleaned
fully on a regular basis, according to the level of use.
Attention should be given to cleaning the baffle system,
flueways and removing ash. Regular cleaning and preventive
maintenance will help give many years of safe use.
1.2 The external paintwork may be cleaned using warm soapy
water and a soft clean cloth. Wipe dry with a soft clean
cloth before re-lighting. Do not leave unit without drying, as
this may cause rust.
2. CLEANING GLASS
2.1 While the correct use of the Airwash system, and good
quality fuel, will generally keep the glass clean when the
appliance is used you may sometimes need to clean the
glass.
2.2 This can be done as follows. Allow the Yeoman stove to
cool fully, never attempt to clean hot glass. Any deposits
can be removed using a soft cloth and Glass Cleaner.
2.3 Before re-lighting the appliance, dry the glass fully.
2.4 Do not use abrasive cleaner or cleaning pads.
3. CHIMNEY SWEEPING
3.1 We would recommend that to maintain the safe and
efficient use of the appliance the flue / chimney is inspected
and swept at least once a year, by a NACS Registered
(UK only)/ INFO Registered (Eire only) chimney sweep
who will issue you with a certificate confirming the work
completed and the condition of the flue/chimney.
4. ANNUAL SERVICE
At the end of the heating season it is recommended once
the stove is cold, to strip, inspect and clean the stove as
detailed: -
4.1 Carefully remove all of the following internal parts. Internal
Baffle, Complete grate, and Ashpan. See sections 5 and 6
pages 10 and 11 for the instructions on how to remove the
baffles.
4.2 Vacuum clean any remaining ash and debris from the inside
of the stove. We offer a filter/collection unit that attaches to
and protects your vacuum cleaner from the fine ash. Ash
Clean (Part no. 2091).
4.3 Clean the internal surfaces, baffles and grate parts of the
stove using a wire brush and scraper as required and check
the parts for any damage. Replace any damaged parts.
Vacuum and brush the resulting debris from the stove, then
give the inside of the stove a protective coating of light oil
such as WD40®.
4.4 Check the parts for any damage. Replace any damaged
parts.
4.5 Re-fit cleaned internal parts.
4.6 Remove the glass from the doors, see section 7, page 11
and discard all old rope seals.
4.7 Remove the door rope seal from the outer edge of the
doors and clean the old glue from the door sealing rope
groove.
4.8 Clean the door glass using Stove Glass Cleaner and
a soft cloth, do not use abrasive cleaners to remove tar or
soot deposits from the glass.
4.9 Replace the glass edge seal with new and re-fit the glass into
place in the doors.
4.10 Fit new door rope seal, gluing it in place with a generous
bead of Thermic Seal Glue into the rope locating groove.
Press the new door sealing rope into the locating groove,
placing the joint in the middle of the lower edge
of the door. When fitting new door seals we recommend
closing the stove door and leaving for at least 12 hours
before using. This allows the adhesive to fully bond to the
seal before use.
4.11 Lightly oil the door catch mechanisms and hinge pins. Avoid
getting oil onto the door seals and glass.
4.12 To refresh painted finishes it is possible to re-paint using
stove paint.
4.13 We recommend that only genuine Yeoman replacement
parts are used to keep your appliance in safe and efficient
working order. Your local Yeoman dealer will be able to
provide you with the genuine parts you require.
MAINTENANCE and SERVICING
See chart on page 10 for common spare parts referred to in this section.
For a complete list of spare parts and accessories contact your Yeoman dealer for the Stovax
Fireplace, Stove & Hearth Accessories Brochure or call 01392 474011