Specifications – Viking MCX-106 User Manual
Page 13
MIXER SECTION
Frequency Response
+0, -3dB 30Hz~20kHz (HIGH Z input TRIM at "0" positio
Total Harmonic Distortion
0.05% +4dBm at 1kHz.
Hum and Noise (Open)
Equivalent Input Noise
-130dBm (20Hz~20kHz
Equivalent Input Noise
-133dBm (IHF A)
All level Controls Minimum
-102dBm (IHF A)
PGM Master at MAX and all
input level controls minimum -93dBm (IHF A)
PGM Master at MAX and one
input level control at MAX
-72dBm (IHF A)
Maximum Voltage Gain
INPUT to PGM out
59dB
INPUT to EFF out
45dB
INPUT to FB out
59dB
INPUT to REC o u t
45dB
INPUT to GEQ out
59dB
AUX to PGM out
14dB
EFF/RET to PGM out
24dB
Equalization
63Hz ±12dB Peaking
2kHz ±12dB Peaking
125Hz ±12dB Peaking
4kHz ±12dB Peaking
250kHz ±12dB Peaking
8kHz ±12dB Peaking
500Hz ±12dB Peaking
16kHz ±12dB Peaking
1kHz ±12dB Peaking
Peak Indicators
Red LED on each input channel LED's t u r n on at 3dB below
clipping.
INPUT SPECIFICATIONS
CONNECTION
INPUT
ACTUAL
LOAD
IMPEDANCE
FOR USE
WITH
NOMINAL
TRIM
POSI-
TION
SENSITIVITY
(PGM OUTPUT
LEVEL +4dB)
MAX BEFORE
CLIP INPUT
LEVEL
CONNECTOR
XLR TYPE NC3F
CH1
CH6
AUX (L & R)
EFF/RET
GEQ
PWR
BUSS LINK
(PGM, FB, EFF)
LOW Z
HIGH Z
OPEN
10
0
10
0
-55dBm (1.38mV)
-16dBm (123mV)
-35dBm ( 13.8m V)
+4dBm (1.23mV)
-l0dBm (245mV)
-20dBm (77.5mV)
+4dBm (1.23V)
+4dBm (1.23V)
+4dBm (1.23V)
-34dBm (1 5 m V )
+1.7dB (0.94V)
-14dBm (150mV)
+20dB (7.75V)
+8dBm (1.9V)
-2dBm (0.61V)
+20 dBm (7.75V)
OUTPUT SPECIFICATIONS
CONNECTION
ACTUAL LOAD
IMPEDANCE
FOR USE WITH
NOMINAL
OUTPUT LEVEL
NOMINAL
MAX. BEFORE
CLIP
CONNECTOR
PHONE JACK
PHONE JACK
PHONE JACK
PHONE JACK
RCA P I N JACK
RCA PIN JACK
+4dB (1.23V)
+10dB (245V)
+4dB (1.23V)
+4dB (1.23V)
-l0dB (7.75V)
0dB (0.775V)
+20dB (7.75V)
+8dB (1.9V)
+20dB (7.75V)
+20dB (7.75V)
+8dB (1.9V)
+20dB (7.75V)
PGM
EFF
GEQ
FB
REC L & R
TAPE L & R
Total Harmonic Distortion
Less than 0.1% (200mW~200W RMS, 20Hz~20kHz)
Typically below 0.05%
Compressor Dynamic Range
Greater than 26dB
Hum and Noise
At least 110dB S/N ratio, 20Hz~20kHz
At least 113dB S/N ratio IHF-A weighted
Output Connector
Phone Jack X2
Power Requirement
600 W 120V AC 50/60Hz
Dimensions (WXHXD)
605X371X356mm (23.8X14.6 X14.0) inch
Weight
27.2 kg (60 I b s )
*0dBm is referenced to 0.775V RMS.
Specifications are s u b j e c t to change w i t h o u t notice.
POWER AMPLIFIER SECTION
Frequency Response
MICRO-
PHONES
LOWER IMP
LINES
LOWER IMP,
LINES
LOWER IMP,
LINES
LOWER IMP,
LINES
LOWER IMP
LINES
LOWER IMP
LINES
+0, -1dB 5Hz to 40kHz (200W RMS
Rated Power & Load
300W RMS
200W RMS
120W RMS
Power Output at Clipping
1% THD, 1kHz
348W RMS
238W RMS
140W RMS
— 12 —
Damping Factor
Greater than 200 (1kHz
Input Sensitivity
+4dBm (1.23V)
Input Impedance
IMP. LINES
IMP. LINES
IMP. LINES
IMP. LINES
IMP. LINES
IMP. LINES
PHONE JACK
PHONE JACK
RCA PIN JACK
PHONE JACK
PHONE JACK
PHONE JACK
PHONE JACK
Specifications