Viking F20497 - Manual (Page 7)

13
FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the
refrigerated beverage center should be washed thoroughly with hot, soapy water, rinsed and wiped dry to remove
film residue and any installation dust or debris before being used. Solutions stronger than soap and water are rarely
needed.
2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive
cloths, cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot,
wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other
metal tool to scrape stainless steel; scratches are almost impossible to remove.
12
ELECTRICAL CONNECTION
E Elle eccttrriicca all R Re eq qu uiirre em me en nttss
A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is
required. (A time delay fuse or circuit breaker is recommended.) It
is recommended that a separate circuit, serving only this appliance,
be provided.
• •E EL LE EC CT TR RIIC CA AL L G GR RO OU UN ND D IIS S R RE EQ QU UIIR RE ED D O ON N T TH HIIS S A AP PP PL LIIA AN NC CE E..
• •D DO O N NO OT T U UN ND DE ER R A AN NY Y C CIIR RC CU UM MS ST TA AN NC CE ES S R RE EM MO OV VE E T TH HE E P PO OW WE ER R
S SU UP PP PL LY Y C CO OR RD D G GR RO OU UN ND D P PL LU UG G..
• •D DO O N NO OT T U US SE E A AN N E EX XT TE EN NS SIIO ON N C CO OR RD D
R Re ecco om mm me en nd de ed d G Grro ou un nd diin ng g M Me etth ho od dss
For your personal safety, this refrigerated beverage center must be grounded. This appliance is equipped with a 7’ (2.1
m) power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged
into a mating 3-prong grounding type wall receptacle grounded in accordance with the National Electrical Code and local
codes and ordinances. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of
the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local
codes and ordinances. The third ground plug SHOULD NOT, under any circumstances, be cut or removed. All UL listed
refrigerated beverage centers are equipped with this type of plug.
Power Supply with
3-prong grounding
plug
Grounding type wall
receptacle
LIGHT BULB REPLACEMENT - 24” W. Models
This unit uses a 15-watt incandescent bulb located behind the display housing.
To replace the light bulb:
1. Unscrew the old light bulb located behind the display housing.
2. Discard the old light bulb.
3. Screw new light bulb into location behind the display housing.
E EN NE ER RG GY Y S SA AV VIIN NG G T TIIP PS S
•Reduce door openings.
•Close the door as soon as you can.
•Keep the condenser coils on bottom of the refrigerated beverage center clean. (See “Cleaning and Maintenance”.)
•Adjust the temperature control to a warmer setting when practical.
•Do not put hot foods in the refrigerated beverage center.
•Install unit away from the stove or other heat sources.
LIGHT ASSEMBLY REPLACEMENT - 15” W. Models
NOTE : Please contact your Viking Range
Corporation parts distributor or dealer to order
new light assembly.
To replace the light, first disconnect the
refrigerated beverage center’s power cord. Next,
remove both the green ground wire screw located
on the left of the light assembly and the other
screw located on the right of the light assembly
with a 5-16” hex head screwdriver. (See drawing).
Unplug the light unit and remove complete light
assembly.
To install the new light assembly, screw in the
green ground wire screw and the screw located on
the right with a 5/16” hex head screwdriver and
plug the light unit in.
Plug
Hex head
screw
Light
assembly Green
ground wire
Hex head
screw
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical shock.
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical shock.
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical shock.
WARNING
LEG LEVELER INSTALLATION
R Re ea ad d B Be effo orre e IIn nsstta alllliin ng g L Le eg g L Le evve elle errss
1. Four leveling legs are pre-installed in the base of the unit at the factory.
2. The unit should be leveled from front to back and side to side. If floor
conditions do not allow the unit to sit level, adjust the leg levelers by turning
the required leg leveler counter-clockwise to increase the height and clockwise
to reduce the height.
WARNING
Do not lay unit on top, side, back, or front. If unit is accidentally laid in
any position other than right side up, then the unit must remain in the
upright position for at least 24 hours before plugging the unit in.