Tannoy V12HP - Manual (Page 10)

11. Technical Specifications
Frequency Response (1) +/- 3dB 67Hz - 23kHz
55Hz - 25kHz (with Tx2/TDx2 controller)
-10dB Point 57Hz (50Hz with Tx2/TDx2 controller)
Recommended Amplifier Power
(passive Full Range) 350 - 700 watt / 8 ohm
Power Handling(2) Average(2) Programme Peak (10ms)
Passive Full Range 350 watt 700 watt 1400 watt
Biamp (LF) 350 watt 700 watt 1400 watt
Biamp (HF) 60 watt 120 watt 240 watt
Sensitivity (1)
2.83 volt @ 1m Passive Full range 99dB (anechoic) 102dB (half space)
Biamp (LF) 99dB (anechoic) 102dB (half space)
Biamp (HF) 106dB (anechoic)
Maximum SPL (3) Average Peak
@ 1m Passive Full Range 124 dB 130 dB
Biamp (LF) 124 dB 130 dB
Biamp (HF) 124dB 130dB
Impedance
Nominal 8.0 ohm (passive fullrange & each driver biamp)
DI Averaged (PCQ) 10.35, 500 Hz - 16 kHz
@ 1kHz (ISO) 6.35
@ 2kHz (ISO) 10.82
@ 4kHz (ISO) 9.2
@ 8kHz (ISO) 13
@ 16kHz (ISO) 15.8
Q Averaged (PCQ) 14.6, 500 Hz - 16 kHz
@ 1kHz (ISO) 4.93
@ 2kHz (ISO) 12.08
@ 4kHz (ISO) 8.32
@ 8kHz (ISO) 19.95
@ 16kHz (ISO) 38
Distortion
0.1 Full Power 2nd Harmonic 3rd Harmonic
250 Hz 0.32% 0.89%
1000 Hz 1.58% 3.54%
10000 Hz 5.62% 0.19%
0.01 Full Power 2nd Harmonic 3rd Harmonic
250 Hz 0.11% 0.71%
1000 Hz 0.79% 2.53%
10000 Hz 1.94% 0.161%
Driver Complement 1 x 12” (300mm) PowerDual
Constant Directivity Dual Concentric Type number 3190
Crossover Point Passive 1.5kHz
2nd order high pass, 2 nd order low pass
Product can be reconfigured for active / bi-amped operation
Active system parameters available in section 13 of manual
Enclosure 37.5 litre vented, Birch plywood
Finish Textured black paint (optional in white)
Protective Grille Foam covered, powder coated perforated steel
Connectors 2 x Speakon NL4MP IN/OUT
Configuration for biamp operation via the termination panel.
Fittings Recessed rear mounted carrying handle,
Blanking plate allows installation of a 35mm pole-mounting socket,
8 x M10 bracket inserts allowing for landscape or portrait orientations,
8 x M10 flying inserts.
Dimensions 486mm(H) x 370mm(W) x 375mm(D)
19.13”(H) x 14.57”(W) x 15.15”(D)
Weight 22 Kg (48.4 lbs)
NOTES: (1) Average over stated bandwidth. Measured at 1m on axis.
(2) Long term power handling capacity as defined in EIA standard RS - 426A.
(3) Unweighted pink noise input, measured at 1m in an anechoic chamber
All Tannoy V Series products can be used with the Tannoy TDX2 Digital Controller for optimum system performance and when
being used with various sub bass systems. Please visit our website at
www.tannoy.com for further details
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods
will always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior notice.
Please verify the latest specifications when dealing with critical applications.