Tascam MD-801R/P Mk II - Manual (Page 25)

TASCAM MD-801R/P Mk II
4–1
4 - Basic operations
This section gives you informstion about the basic
operations using the MD-801.
It assumes that you have connected the MD-801 to
all the other equipment that you will be using. If you
have not already made these connections, read 2.3,
"Rear panel" for details of the rear panel connections,
and connect the other equipment appropriately.
4.1 Inserting and ejecting discs
Discs are inserted label side uppermost, in the direc-
tion of the arrow marked on the disc. The display
shows:
if the MD-801 is turned on without a disc in the
drive.
As the disc is loaded, the display shows:
When the disc has been loaded, the disc title, number
of tracks, total running time, etc. are displayed.
Use the EJECT key [3] to eject discs.
Discs do not have to be ejected when the power to
the MD-801 is turned off. No damage will be caused
to discs if they are left in the unit at power-off or
power on.
NOTE
Never turn the power off when the U-TOC is
being written to disc (
UTOC Writing ).
If you do, the disc may become unreadable.
When the MD-801 is turned on with a disc already
loaded in the drive, the display will show:
before showing the disc title, running time, number
of tracks, etc.
4.2 Playback of discs
The following instructions apply to both pre-
recorded and recordable MD media.
4.2.1 Playing back a whole disc
When the disc has been loaded, and the TOC has
been read, use the
PLAY MODE key so that the
playback mode is not set to S I N G L E or A - B (see [22] ).
Press the PLAY key [6] . Playback will start from the
beginning of the disc.
Stop playback with the STOP key [5] .
Pause playback with the READY key [7] and restart
it with the PLAY key.
NOTE
If the tracks being played back are less than
three seconds in length, playback will be dis-
continuous (“jumpy”).
4.2.2 Playback outputs
There are two sets of outputs provided on the MD-
801: the
LINE balanced XLR-type at +4 dBu [40] ,
and the MONITOR unbalanced RCA at –10 dBV
[38] .
OUTPUT MODE DIP switch 2 [39] on the rear
panel is used to synchronize these outputs so that
material is always played back through both sets of
outputs (off), or individually (on).
If the individual output option is chosen, the PLAY
key on the MD-801 itself or the MONITOR key on
the RC-801 will start playback through the
MONITOR outputs only. In this case, the LINE out-
puts are activated following a play or online com-
mand from a remote controller (keyboard, RC-801,
RC-8 or the serial or parallel controller).
If the the LINE outputs are used for playback, the
MONITOR outputs may also be used for simulta-
neous playback. OUTPUT MODE DIP switch 3
controls this. When set to off, the MONITOR out-
puts are muted when the LINE outputs are in use.
When set on, the MONITOR outputs are always
used.
The PHONES jack [9] is always used.
The above applies to the analog outputs only, and
does not refer at all to the digital outputs, which are
always in use, regardless of the origin of the play-
back command.
4.2.3 Monaural playback
OUTPUT MODE DIP switch 1 [39] is used to com-
bine the left and right tracks and output them from
both the left and right outputs equally.
The outputs affected are the LINE [40] , MONITOR
[38] and PHONES outputs. The digital outputs are
not affected by the position of this switch.
N O D I S C
D i s c L o a d i n g
T O C R e a d i n g