Technicolor - Thomson DCD-SA1 - Manual (Page 16)

ENGLISH
16
11 MAIN SPECIFICATIONS
2 Audio [Super Audio CD] [CD]
• Analog output
Number of channels: 2 channels 2 channels
Frequency response: 2 ~ 100,000 Hz 2 ~ 20,000 Hz
Frequency response range: 2 ~ 50,000 Hz (–3 dB) 2 ~ 20,000 Hz
Signal-to-noise ratio: 117 dB 120 dB
Dynamic range: 110 dB 100 dB
Harmonic distortion: 0.0005 %(1 kHz) 0.0015 %(1 kHz)
Wow and flutter: Below measurable limit Below measurable limit
Output voltage (UNBALANCED): 2.0 V (10 kΩ/ohms) 2.0 V (10 kΩ/ohms)
Output voltage (BALANCED): 2.0 V (10 kΩ/ohms) 2.0 V (10 kΩ/ohms)
Signal system: 1-bit DSD 16-bit linear PCM
Sampling frequency: 2.822 MHz 44.1 kHz
Discs: Super Audio CD format Compact Disc format
• Digital output
Coaxial: – 0.5 Vp-p/75 Ω/ohms
Optical: – –15 ~ 21 dBm
Light emission wavelength: – 660 nm
• Digital input
Format: Digital audio interface (Linear PCM)
Coaxial: 0.5 Vp-p/75 Ω/ohms
Optical: Light emission input: –27 dBm or more
Light emission wavelength: 660 nm
2 General characteristics
Power supply:
AC 230 V, 50 Hz
Power consumption: 35 W
Maximum external dimensions: 434 (width) x 150 (height) x 410 (depth) mm (including protruding parts)
Mass: 21.8 kg
2 Remote control unit: RC-997
Type: Infrared pulse system
Power supply: DC 3 V, 2 R03/AAA batteries
Maximum external dimensions: 44 (width) x 233 (height) x 22 (depth) mm
Mass: 165 g (including batteries)
✽ Design and specifications are subject to change without notice.
Check again before assuming the player is malfunctioning
10 TROUBLESHOOTING
2 Are all the connections correct?
2 Are you following the instructions in the operating instructions?
2 Are the amplifier and speakers operating properly?
If the DCD-SA1 does not seem to be functioning properly, check the table below. If this does not solve the problem, the DCD-SA1 may be
defective. Turn off the power, unplug the power cord from the power outlet, and contact your store of purchase or nearest Denon sales office.
Disc holder does not open or close.
• Is the power on? .....................................................See page 11.
When a disc is loaded, “NO DISC” is displayed.
• Is the disc loaded properly? ....................................See page 11.
• Are you attempting to play a disc other than a CD or Super Audio
CD?............................................................................See page 9.
When the 1 button is pressed, playback does not start.
• Is the disc dirty or scratched? ...................................See page 9.
There is no sound or it is distorted.
• Is the output cord properly connected to the amplifier?
............................................................................See pages 6, 7.
• Have the amplifier controls been set correctly?
No data is output from the digital output jack
(OPTICAL/COAXIAL).
• With Super Audio CDs, no digital signals
are output..................................................................See page 7.
• Is the DIGITAL OUT button off? ...............................See page 8.
A specific section of the disc will not play.
• Is the disc dirty or scratched? ...................................See page 9.
Programmed playback does not work.
• Has programming been properly done?..................See page 14.
CD-R and CD-RW discs cannot be played.
• For CD-R/-RW discs, has the disc been
finalized?....................................................................See page 9.
Incorrect operation when buttons on the remote control are
pressed.
• Is the remote control unit being operated too far from the CD
player? .....................................................................See page 10.
• Are there obstacles blocking the ray?
• Is the remote control sensor exposed to strong light?
• Are the batteries exhausted?