Transition Networks CGETF10XX-10X - Manual (Page 3)

4
CGETF10xx-10x
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Installation
-- Continued
Install the slide-in-module
CAUTION: Slots in the PointSystem™ chassis without a slide-in-module
installed MUST have a protective plate covering the empty slot for Class A
compliance.
To install the CGETF10xx-10x media converter slide-in-module:
1. Locate an empty installation slot on the PointSystem™ chassis.
2. Carefully slide the slide-in-module into the installation slot, aligning the
module with the installation guides.
3. Ensure that the slide-in-module is firmly seated inside the chassis.
4. Push in and rotate the panel fastener screw (attached to the slide-in-
module) clockwise to secure the slide-in-module to the chassis front.
Install the Fiber Cable
1. Locate or build 1000Base-SX/LX compliant fiber cable with male, two-
stranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the CGETF10xx-10x media converter as
described:
•
Connect the male TX cable connector to the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter,
hub, etc.) as described:
•
Connect the male TX cable connector to the female RX port.
• Connect the male RX cable connector to the female TX port.
10BASE-2
CECF100 CFMFF100
0 50½
Link Alert E D
CETCF100 CFETF100 CFETF110 CFMFF100
LA PWR
RXF
RXC
LNK
COL
SPD PWR
FRX
CRX
FLNK
CLNK
100BASE-TX
RX
TX 100BASE-FX
Link Alert E D
0 50½
LA PWR
RXF
RXC
LNK
COL
LKS PWR
LKM
10BASE-2
10BASE-FL 10BASE-T
LKS PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
I 0
TERM INIT
RX
TX
LNK
PWR
CPSMM120
SERIAL
10BASE-T
R
E
S
E
T
LKF PWR
RXF
RXC LKC
I 0
Panel Fastener Screw
Connect the fiber cable
to the media converter
as shown. Connect the fiber cable
to the other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
The slide-in-module is powered through the
Transition Networks PointSystem™ chassis.
[email protected] -- Click the “Transition Now” link for a live Web chat. 5
Installation -- Continued
Install the copper cable
1. Locate or build 1000Base-T compliant copper cables with male, RJ-45
connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the CGETF10xx-10x media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (switch, workstation, etc.).
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter
Operation
Status LEDs
Use the status LEDs to monitor the CGETF10xx-10x media
converter operation in the network.
PWR (Power) ON = Connection to external AC
power.
LKF (Fiber link) ON = Fiber link connection.
LKC (Copper link) ON = Copper link connection.
RXF (Fiber receive) Flashing = Reception of data on
the fiber link.
RXC (Copper receive) Flashing = Reception of data on
the copper link.
10
0
RX
TX 1000Base-SX/LX
PWR
RXF LKF
RXC LKC